User manual FANOTEC NODAL NINJA 3 QUICK REFERENCE GUIDE

[. . . ] These components are critical for the effective reduction of total dissolved solids and specific contaminants that are listed in the Appendix. The Merlin drinking water system does not have a monitoring device for contaminants. To verify that the system is performing satisfactorily the product water should be tested periodically by the system's installing dealer every six months. See the back cover of this manual for the installing dealer's contact information. [. . . ] If threaded fittings are used, be sure to use pipe joint compound or Teflon tape on outside threads. Turn the valve off. 8 Rev B THE BASIC REVERSE OSMOSIS SYSTEM STEP 2: INSTALL DRAIN ADAPTER Follow the instructions in the Appendix for installation of the Drain BoaTM. The drain adapter is designed to fit 1-1/2-inch (3. 8 cm) sink drain pipe. The adapter installs directly to the sink tailpiece. Be sure it will fit flat against the sink or counter and that there is space underneath for tubing. If drilling is needed, make a 1-1/8-inch to 1-1/4-inch diameter hole. WARNING: To avoid damaging a sink, consult a qualified plumber or installer for the proper method of drilling holes in porcelain or stainless steel. Gasket Air Gap Module Horseshoe Clip Washer Trim Ring Standoff Nut Water In Connection Figure 3 THE BASIC REVERSE OSMOSIS SYSTEM 9 Rev B B. Assemble Faucet The tubing and fasteners are assembled to the faucet before the faucet is placed in position. If not using the air gap module, skip to step #3. If the air gap feature is used, place the gasket in position on the faucet. Slide the decorative ring over the tubing connections and up to the bottom of the faucet. The use of sterile/latex gloves is recommended. Lubricate element O-rings, brine seals, and sump O-rings with silicone lubricant. Securely insert O-ring end of membrane elements into manifold. Remove carbon/sediment prefilter from packaging. Pressure Test System To check for leaks, the system must be filled with water and brought up to operating pressure. Run at 1/2 open for a minute, then open fully. Open faucet until water runs. 14 Rev B THE BASIC REVERSE OSMOSIS SYSTEM 3. NOTE: When the faucet is initially turned on, water may temporarily sputter from the air gap until the air is purged. Allow 1 to 3 hours for any trapped air noise in the system to subside. Open the faucet and run the water through the RO system for one hour. NOTE: The one hour flush removes a food grade preservative from the membrane elements. [. . . ] This flush removes the food grade preservative from the elements. The preservative is not harmful but may affect the taste of the water. The RO system is now ready for use. REPLACEMENT OF THE PREFILTER, POSTFILTER, AND RO MEMBRANE ELEMENTS 19 Rev B APPENDIX 20 Rev B APPENDIX ME R L IN S Y S T E M 1255052 OnDemand RO T UB ING INS T AL L K IT P N 1255736 P N 1239708 P N 1240564 P N 1244617 R E P L AC E AB L E C AR T R IDG E S P N 1254894 S UMP & S E AL S UP P OR T LE G DR AIN B OA K IT AIR -G AP F AUC E T K IT C OMP L E T E MANIF OL D MERLIN COMPONENTS 3/8" B L AC K T UB ING P N 1237460 P N 1239705 P R E -F IL T E R S UMP 3/8" B L UE T UB ING E L E ME NT 1/2" NAT UR AL T UB ING P N 1240326 P N 1238342 (2) O-R ING 1/2" R E D T UB ING P OS T -F IL T E R P N 1244746 F IT T ING S & L OC K ING B AR INS T AL L K IT P N 1255693 L OC K ING B AR DIS C ONNE C T P N 1239731 MERLIN COMPONENTS C OL L E T L OC K C L IP RED P N 1240626 (1) C OL L E T L OC K C L IP W HIT E P N 1240627 (5) C OL L E T L OC K C L IP B L UE P N 1240628 (2) DR AIN DIS C ONNE C T E LB OW - DK G R AY P N 1240116 FE E D DIS C ONNE C T E L B OW - W HIT E P N 1240117 P E R ME AT E DIS C ONNE C T E L B OW - B L UE P N 1240118 F L US H DIS C ONNE C T E L B OW - L T B L UE P N 1240119 P L UG 1/4" P N 1240624 F AUC E T C ONNE C T ION F IT T ING P N 1240625 S IL IC ONE L UB R IC ANT S G L US E T UB E P N 1013501 (2) SILICONE LUBRICANT Spare parts are available through your installing water treatment dealer. 21 Rev B MERLIN PARTS LIST Part Number 1255052 1239705 1244617 1239708 1240564 1240620 1240621 1240622 1240623 1240117 1240118 1240116 1240119 1239731 1240326 1254894 1255693 1255736 Complete Merlin system Sump - interchangeable for all 3 positions Manifold - complete Support Leg Drain Boa Kit 3/8-inch Black Tubing - 500 foot roll - John Guest Brand 3/8-inch Blue Tubing - 500 foot roll - John Guest Brand 1/2-inch Natural (clear) - 250 foot roll - John Guest Brand 1/2-inch Red Tubing - 250 foot roll - John Guest Brand 1/2-inch Feed Disconnect Elbow - White 3/8-inch Permeate Disconnect Elbow - Blue 3/8-inch Drain Disconnect Elbow - Dark Gray 1/4-inch Flush Disconnect Elbow - Light Blue Locking Bar Sump O-Ring Airgap Faucet Complete Fittings and Locking Bar Kit Complete Tubing Install Kit Description REPLACEABLE CARTRIDGES Part Number 1238342 1237460 1244746 Membrane Element Carbon Prefilter Carbon Postfilter Description Spare parts are available through your installing water treatment dealer. 22 Rev B MERLIN PARTS LIST ACCESSORIES Part Number 1261345 1240619 1240632 1013501 1240629 1240630 1262403 1262404 1262406 1262407 1262408 1262847 -- Description Merlin Flush Kit (Accumulator tank and 1/4-inch tubing) 1/4-inch Blue Tubing - 500 foot roll - John Guest Brand Inlet Booster Pump, 110V/60Hz Silicone Lubricant Pack Feed Valve Tee - 1/2" x 1/2" x 1/2" OD Tubing - G. A. Murdock USA Feed Valve Tee - 5/8" x 5/8" x 1/2" OD Tubing - G. A. [. . . ]