User manual FARSTONE DRIVECLONE 2

[. . . ] DriveClone TM Version 2. 0 User's Guide Copyright Notice No part of this publication may be copied, transmitted, stored in a retrieval system, or translated into any language in any form or by any means without the expressed written permission of FarStone Technology, Inc. FarStone grants you the right to use one copy of the enclosed software program ("SOFTWARE") on a single computer. If the SOFTWARE is installed on a network, or more than one user can run the SOFTWARE at the same time, you must purchase an additional license for each additional user or computer. Trademarks FarStoneTM and DriveCloneTM are trademarks of FarStone Technology, Inc. Microsoft®, Windows® and MS-DOS® are registered trademarks of Microsoft Corporation. [. . . ] The erased data can still be recovered using special tools. Full Erase: Full Erase will physically erase the entire disc. Compared to Quick Erase, Full Erase will take a longer time to complete, but it is less likely to run into a disc error when using a full erased disc to burn again. 4. 5 Settings You can set a standard for using the USB devices, and your local network configurations. 4. 5. 1 Set USB Standard DriveClone can back up to or restore from an image file that is on a USB device. DriveClone supports USB 1. 1 and USB 2. 0 standards. To set a defaultUSB standard for your device, click Settings (shown below), choose a USB standard and click Apply. 18 Note If you select USB 2. 0, please make sure all your USB devices, eg. the USB storage medium, the port and the host adapter card, can support USB 2. 0. Otherwise, it will automatically revert to USB 1. 1 speed. 4. 5. 2 Network Settings DriveClone can back up to, or restore from a network location. To use this feature, you should first configure your network settings. To configure your network settings, click Settings from the main DriveClone interface and then click the Settings button in under Network. There are two tabs in the Network Settings window: General: The General tab is shown below. You can setup your network adaptor, IP address, Subnet mask and Default gateway from here. If you have more than one network adaptor on your system, select the adaptor to be used from the dropdown menu. IP Settings: Obtain an IP address automatically: If your network supports DHCP (Dynamic Host Configuration Protocol), choose this option to obtain an IP address automatically from a DHCP server or a Point-to-Point Protocol (PPP) dial-up network access server. DriveClone uses DHCP as the default option and will obtain the IP address of your computer automatically. IP address: Choose this option to manually specify IP address for your network. This option can be used when automatically obtaining IP address fails or the there is an IP address conflict. Advanced The Advanced tab is shown as below. 19 If your computer is on a Local Area Network (LAN), you can set the LAN settings so that you can back up images to or restore from a network location. DNS settings: Obtaining DNS server address automatically: DNS (Domain Name System) is an internet service that translates domain names into IP addresses. It is a system for name resolution suitable for network computers with fixed IP addresses. By default, DriveClone uses this option to obtain the DNS sever address automatically from the network. Use the following DNS server addresses: Choose this to manually specify the DNS server addresses if needed. WINS: Specify an IP address for a WINS server. Windows Internet Naming Service (WINS) is a system that determines the IP address associated with a particular network computer. It supports network client and server computers running Windows and can provide name resolution for other computers with special arrangements. [. . . ] User License: (a) The "Software" can be used on a single computer and only by a single user at a time. (b) You can make one copy of the "Software" in machine-readable form, solely for back-up purposes, provided you reproduce FarStone's copyright proprietary legends. Notwithstanding the foregoing, the "Software" may be used on the home, laptop or other secondary computer of the principal user of the "Software", and an additional copy of the "Software" may be made to support such use. As used in this License, the "Software" is "in use" when it is either loaded into RAM or installed on a hard drive or other permanent memory device. [. . . ]