User manual FAURE CHM151X

[. . . ] · When installed between adjoining wall cabinets the wall cabinets must not overhang the hob. · If the room where the hood is to be used contains a fuel burning appliance such as a central heating boiler then its flue must be of the room sealed or balanced flue type. · If other types of flue or appliances are fitted ensure that there is an adequate supply of air to the room. · The ducting system for this appliance must not be connected to any existing ventilation system which is being used for any other purpose. [. . . ] Never use scouring pads or abrasive cleaners. Never use excessive amounts of water when cleaning particularly around the control panel. Metal Grease Filters The grease filter absorbs grease and dust during cooking to help keep the appliance clean inside, and should be cleaned approximately once every month or more often if the hood is used for more than 3 hours a day. Remove the metal grease filters one at a time by: Releasing the catches on the filters, the filters can now be removed. The metal grease filters should be washed, by hand, in mild soapy water or in a dishwasher. Allow to dry completely before replacing. 6 Charcoal Filters In the recirculation mode the charcoal filters absorb smells an unwanted odours. The charcoal filters cannot be cleaned, we recommend they should be replaced approximately every three months or more often if the hood is used for more than three hours per day. To Remove/Replace the Charcoal Filters 1. Twist the charcoal filter anti-clockwise and remove. To replace the charcoal filters, remove the metal grease filters. Place one filter over the inlet grille at either end of the fan housing and twist into position. This appliance can be a fire hazard if the grease and charcoal filters are not cleaned and replaced as recommanded. Changing the Light Bulb 1. Loosen and remove the screws and brackets retaining the glass cover. Lever out the brackets and slide the glass cover to the right. · The guarantee is for the same period and to the same extent for labour and parts as exists in the new country of use for this brand or range of products. · This guarantee relates to you and cannot be transferred to another user. · Your new home is within the European Community (EC) or European Free Trade Area. · The product is installed and used in accordance with our instructions and is only used domestically, i. e. Before you move please contact your nearest Customer Care Centre, listed below, to give them details of your new home. They will then ensure that the local Service Organisation is aware of your move and able to look after you and your appliances. France Germany Italy Sweden UK Senlis Nurnberg Pordenone Stockholm Newbury +33 (0)3 44 62 22 22 +49 (0)911 323 2600 +39 (0)1678 47053 +46 (0)20 78 77 50 +44 (0)1635 522 799 9 INSTALLATION INSTRUCTIONS It is dangerous to alter the specifications or attempt to modify this product in any way. Technical Information DIMENSIONS HEIGHT CANOPY: HEIGHT CHIMNEY WIDTH CANOPY DEPTH: UPPER SECTION LOWER SECTION 24cm 40cm 36cm 60cm 49cm 220-240 V 225W 145W 80W ELECTRICAL SUPPLY: POWER CONSUMPTION: FAN MOTOR: LAMP: SUITABLE FOR INSTALLATION ABOVE: Voltage (50Hz) 2 x 40 ELECTRIC HOB: GAS HOB: SLOT-IN GAS COOKER SLOT-IN ELECTRIC COOKER 7KW (max) 10KW (max) 13. 5KW (max) 12. 4KW (max) Note: CE Marking certifies that this appliance complies with the requirements laid down in EEC directive 89:336. (Electromagnetic compatibility) and subsequent modifications and Low Voltage directive 72/23/E. ELECTRICAL CONNECTIONS This appliance must be earthed Electrical Requirements Any permanent electrical installation must comply with the latest I. E. E. Regulations and local Electricity Board regulations. For your own safety this should be undertaken by a qualified electrician e. g. your local Electricity Board, or a contractor who is on the roll of the National Inspection Council for Electrical Installation Contracting (NICEIC). [. . . ] Hook the canopy hood C, into the wall fixing brackets ensuring the security fixing screws align with the holes in the centre of the back panel as illustrated. Insert the two M4 x 25m canopy adjustment screws, into the wall brackets, from the underside of the hood. The canopy can be aligned and adjusted in height by using the two adjustment screws (W). Before fitting the chimney to the canopy make the electrical connection as described in the sectione titled "ELECTRICAL CONNECTION". [. . . ]