User manual FAURE CHM161X

[. . . ] Technical safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Special information for gas cookers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Proper use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Correct installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operating modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Exhaust-air mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The extractor hood must not be installed over a solid fuel heating appliance which may be a fire risk (e. g. flying sparks) unless the heating appliance has a closed, nondetachable cover and the country-specific regulations are observed. This restriction does not apply to gas cookers and gas hobs. To avoid damaging the hob, cover it when installing the extractor hood. RISK OF FIRE Do not flambé under the extractor hood or work with a naked flame. When switched on, the extractor hood draws flames into the filter. There is a risk of fire due to deposits on the grease filter!Do not leave pans, frying pans or deep-fat fryers unattended if you are cooking food with oils or fats, e. g. Overheated oils or fats can easily ignite!A risk of fire can be prevented by cleaning the grease filters regularly and changing the activated-carbon filter in good time. Never operate the extractor hood without grease filters. 7 Operating modes The extractor hood can be used in exhaust air and circulating air mode. Exhaust-air mode Appliance dimensions Exhaust air min. 580 max 1. 030 The air which is drawn in is cleaned by the grease filters and conveyed to the exterior by a pipe system. min. Remove the grease filters (see Removing and installing the metal-mesh grease filters). 2. Reinsert the grease filters (see Removing and installing the metal-mesh grease filters). Changing the activated carbon filter Under normal operation (daily 1 to 2 hours) the activated carbon filters must be replaced approximately 2x year. The activated carbon filter is available from specialist outlets, customer service or the Online Shop (see Optional accessories). Activated carbon filters do not contain any pollutants. They can be disposed of in the household refuse. (for appliances with edge extraction) 2. Reinsert the cleaned grease filters. 11 Changing the bulbs Before changing the bulbs, always follow the instructions and warnings in the chapter entitled "Safety instructions"!The description of changing the bulbs applies to several appliance models. NOTE: Observe the warranty regulations in the enclosed service booklet. Changing the filament bulbs 1. Push the bulb cover towards the middle of the appliance. 2 1 Changing the halogen bulbs Halogen bulbs become very hot during operation. Even some time after the appliance has been switched off, there is still a risk of burns!Before changing the halogen bulbs, ensure that they have cooled down fully. [. . . ] The enclosed screws and wall plugs are suitable for solid brickwork. Use the appropriate fixing materials for other wall structures (e. g. plaster board, porous concrete, poroton bricks). Ensure that the wall has adequate load bearing capacity. [. . . ]