User manual FBII XL-20

[. . . ] 9 ARMING THE SYSTEM (CONT). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 DISARMING THE SYSTEM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 USER CODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 MISCELLANEOUS COMMANDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] USER LOG VIEW (LCD KEYPADS ONLY) To view the system log, press: + 4 . The zones # + 5 , + 3 + user code. * (*The user code is not required if so programmed by installer. ) When the command is accepted, the display will show the most recent event. Pressing either STAY or D exits this mode. Pressing any other key advances to the next valid log entry. KEY FOB LOW-BATTERY TEST To activate the key fob low-battery test: Press : # then 5 + 6 LED Keypad: An acknowledgement tone is sounded. The test mode is indicated as follows: LCD Keypad: Fixed-Word Keypad: AC Keyfob Bat. Test FO TEST #56 D=Exit When a keyfob button is pressed, the system will provide a display indicating if the keyfob has a low-battery condition. The system exits this mode when the star [D] key is pressed. - 19 - Miscellaneous Commands (cont) ON-LINE DOWNLOAD If enabled by your system installer, an on-line download allows you to initiate a remote communications session with the Central Station (CS) Downloading computer from the control panel location. Typically, the CS initiates a remote communications session. On-line Downloading allows you to call the office (from the same telephone line as the panel), discuss the action required, and allow the CS operator to complete the request while on-line; no additional telephone call is needed. Note that the office number that is dialed should be the phone line that the downloading computer is attached to. On-line connection can be made as follows: 1. The keypad will emit a single acknowledgement chirp as each number is pressed. Press the [#] key after you have made your pager phone number changes. Pressing the [#] key saves your new pager number and nulls out the remaining locations. To exit without saving changes, press the [G] key to exit pager phone number programming. An acknowledgement tone sounds to indicate pager number programming has been exited. If you press the [G] key without first pressing the [#] key to save your new pager phone number, the system exits the pager phone number programming mode without saving the changes. If no key is pressed within 10 seconds, the pager phone number programming mode times out and exits automatically without saving any information entered. TURN PAGER REPORTING ON/OFF FOR THE PARTITION You can turn on/off the open-close reporting feature for a partition by pressing # , 8 . The display prompts you to toggle the feature on/off with the [#] key. TURN PAGER REPORTING ON/OFF FOR A USER You can turn on/off the open-close reporting feature for a user by entering the following : # , 7 , [master code] [user number] [4] NOTE: The # , 7 command is also used to assign a user to a different partition (see ASSIGNING PARTITIONS TO USERS on page 14). - 22 - Testing the System SYSTEM TEST It is recommended that you test your system once a week using the following procedure: NOTE: If your system is monitored, contact your central station before you perform this test. Then activate the system by opening a protected zone (for example: a window or door). [. . . ] Even persons who are awake may not hear the warning if the alarm is muffled by noise from a stereo, radio, air conditioner, other appliances, or by passing traffic. Finally, alarm warning devices, however loud, may not warn hearing-impaired people or waken deep sleepers. Telephone lines needed to transmit alarm signals from a premises to a central monitoring station may be out of service or temporarily out of service. Telephone lines are also subject to compromise by sophisticated intruders. [. . . ]