User manual FELLOWES PLASMA

[. . . ] DO NOT touch the heating plate while binding - it DO NOT leave the power cord in contact with hot surfaces. DO NOT leave power cord hanging from cupboards or shelves. STORAGE & CLEANING Unplug the machine at the wall. The outside of the machine can be cleaned with a damp cloth. Do not use solvents or flammable materials to polish the machine. 4 BINDING MACHINE CONTROLS A B C D E F G H On/off switch (rear side) Power On button & LED Binding thickness guide Timer selection (increase) Timer selection (decrease) Select / OK button Thickness setting / timer selection Lid I J K L M N O Lid lock (2) Binding channel Document support Illuminated user interface Cooling vents Document clamp (binding) Cooling rack FEATURES & TIPS `System-Check' function When switched on, the machine performs a `System-Check' function. [. . . ] To operate the machine, press the `Power-On' button. · · · · Always put the document into the appropriate sized binding cover. For better results, consider including blank sheets to fill the thermal cover to capacity. Always test bind with a similar size and thickness of thermal covers before final process. Helios has an angled heater mechanism to ensure correct document alignment with the document support during the binding process. For best results, use Fellowes® brand supplies. Thermal binding covers work best with thin and uncoated types of paper. Care should be taken with thick and coated papers to ensure satisfactory results. If the sheets have not been glued completely to the cover, the document can be re-processed to improve the result. Ensure the sheets are well aligned and touching the glued spine of the thermal cover by tapping the collated document in the cover onto a flat surface. This can be done before and after the binding process. · · · · 5 BEFORE BINDING 1. The machine has an integral cooling tray. It can be extended from the back of the machine and can also be pulled upwards to accept larger documents. When the binding cycle is complete, immediately remove the documents and place in the cooling tray or on a flat surface to allow the document to cool. The document can be removed from the machine mid-cycle if required, take care ­ the glue may be hot and melted. 7. 10. 11. 8. 12. NEED HELP? Let our experts help you with a solution. Customer Service. . . www. fellowes. com Always call Fellowes before contacting your place of purchase, see the rear cover for contact details. 6 TROUBLESHOOTING Problem No `red' power on LED No `green' ready light after a long period Possible cause Machine is not switched on Machine is in a hot or humid area Solution Switch on machine at rear next to plug inlet and at the wall socket Move the machine to a cooler and dry area Process the documents again, ensure Binding cover may be too thick to bind Loose and unglued sheets Timer setting may be incorrect The cover size is too small for the number of sheets Loose and glued sheets Extended heating cycle Timer setting may be incorrect Documents left on the heater plate after the cycle is complete Check timer setting is correct. Ensure prompt document removal sheets are in contact with the glued spine by tapping gently on a flat surface Check timer setting is correct and process the document again Check the number of sheets is appropriate for the cover width. Select larger spine width if necessary WORLDWIDE WARRANTY Fellowes warrants all parts of the binder to be free of defects in material and workmanship for 2 years from the date of purchase by the original consumer. If any part is found to be defective during warranty period, your sole and exclusive remedy will be repair or replacement, at Fellowes' option and expense, of the defective part. This warranty does not apply in cases of abuse, mishandling or unauthorised repair. Any implied warranty, including that of merchantability or fitness for particular purpose, is hereby limited in duration to the appropriate warranty period set forth above. In no event shall Fellowes be liable for any consequential damages attributable to this product. [. . . ] Please visit www. fellowes. com/register to register your product and benefit from product news, feedback and offers. Product details can be found listed on the rating plate positioned on the rear side or underside of the machine. 7 FCC CLASS B NOTICE - NOTIFICATION POUR LES ETATS-UNIS Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ]