User manual FELLOWES PS25303540455055DM3 MANUAL-1999

[. . . ] · CAUTION: Do not insert aerosol cleaners or lubricants into or around the machine. Some agents may combust, causing serious injury. · Do not place shredder near water, over a radiator or a heat register. · Do not rest anything on the power cord. [. . . ] · Shredder automatically starts when paper is placed in the entry and stops when finished shredding. Cleaning All Models · Unplug the unit from the wall before cleaning. · Housing can be cleaned with a cloth, dampened with a mild soap and water solution. A B C D US 20# Paper 64 GSM Sheets per Pass 100V/50Hz N/A 7 7 7 7 7 7 7 N/A 7 7 80 GSM 230V/50Hz N/A 5 5 5 5 5 5 5 5 N/A N/A 80 GSM 240V/50Hz N/A 5 5 5 5 5 5 5 5 N/A N/A Sheet Capacity and Usage · Do not exceed recommended sheet capacity for your model. · Folding paper to fit the entry increases the thickness and recommended capacity may be exceeded. · Clips and staples increase the thickness and may decrease sheet capacity. Model: PS55CC PS25 PS25 Plus PS 30 PS30 Plus PS35 & PS40 PS50 PS50 Plus PS55 (non-100/120V) PS55 (100/120V) DM-3/PS45 Sheets per Pass 120V/50Hz 3 5 5 5 5 5 5 5 N/A 7 7 Sheets per Pass Sheets per Pass E F TABLE A Different paper weights and electrical currents will affect capacity. 3 Safety & Maintenance of PS55CC The PS55CC cross cut shredder creates small particles that, if allowed to accumulate, cause the shredder to jam. Follow these simple precautions to significantly reduce the likelihood that particles will accumulate and to keep your cross cut shredder operating at peak efficiency: · Do not allow the basket to overfill. The power of this shredder will compress paper particles into the basket even when it is full. The life of your shredder may be reduced if the cutting system continues to operate with particles packed around it. Reversing helps the shredder flush out small cut particles. Empty basket if it is full before reversing. Oil the cutters: When. . . · Every second or third time you empty the basket; · If the shredder's cutting capacity is diminished; · If the cutting cylinders stop with a squeak or a rubbing sound after power is removed. How. . . A B C D E F Use Powershred Lubricant #35250 or a suitable alternative with an extension nozzle. Alternatives can be 3 in 1 or Sewing Machine Oil. Oil must be non-flammable material and a non-degreaser!Squeeze the lubricant across the full width of the cutters and then turn the machine on and run the cutting system forward for a few seconds. (Since cross-cut machines have auto start, it will be necessary to block the photo eye with a piece of paper in order to run the cutting system forward). Then, depress the reverse button and run the cutting system for a few seconds. Repeat the procedure. Safety of PS55CC · Do not operate PS55CC without the basket it was shipped with. · Do not use without the safety flap. · Do not attempt to defeat the safety interlock switch. Paper Jams 1. Immediately return power switch to OFF (O) position. Depress power switch to the REVERSE (R) position until the jammed paper has been fully removed from the cutter. If the REVERSE (R) function will not operate when pressed, the internal overload protection device has been activated. Release the power switch from the REVERSE (R) POSITION, wait 15 seconds and repeat. If the machine jams in reverse, unplug the unit and cut all excess paper off the top and bottom of the machine before repeating the jam-clearing procedure. [. . . ] In no event shall Fellowes be liable for any consequential or incidental damages attributable to this product. This warranty gives you specific legal rights. You may have other legal rights that vary from state to state. For more detail or to obtain service under this warranty, please contact Fellowes Customer Service at 1-800-9550959, Monday through Friday, 8 AM - 5 PM (Central Standard Time). [. . . ]