User manual FENDER 110-ELC

[. . . ] Connect your Mustang amplifier to your computer's USB port and open the Fender FUSE software. MUSTANG I/II: Press and hold the SAVE button on the amplifier while turning the power switch back on. Continue holding the SAVE button until it starts to blink red. The Firmware Update Instructions will automatically open and give you two options. [. . . ] Effects are separated into four categories: Stompbox, Modulation, Delay and Reverb. EFFECT SETTINGS -- Click and drag any of these knobs to adjust the effect pedal settings. The precise level of each setting will be displayed under the Effect Pedal Selector {B} window. F. BYPASS -- Click on the footpedal switch to turn the effect on-off (bypass). The red light in the upper left corner indicates when the effect is on or off. Youcanalsoclicktheon-offswitchonthesmallerversion oftheeffectpedaliconbelow. You can also adjust the knobs on the smaller version of theeffectpedaliconbelow, whichisconvenientwhenyou areinthePresetEditorwindow. EXCLUSIVE FEATURES: · EFFECTS POSITION Pre­ or Post­Amp · EFFECTS BYPASS These Fender® FUSETM features add functionality beyond what your amplifier provides on its own. Fender FUSE allows you to position your effects before or after the amplifier in the signal path for a wider variety of sonic options. Fender FUSE also allows you to bypass an effect temporarily rather than deleting it and losing all your effect settings each time you want to turn an effect on-off. D. PEDAL COLOR -- Click on any of these color swatches to change the color of the effect pedal. Color changes are for your preference and do not change the sound of the effects. DELETE -- Click on the "X" to remove the effect from the current preset. 4 fender. com 2. 0 Rack Effects Click on any of the four slots {A} to the right of the amplifier icon to select an effect and open the Rack Effects edit screen. These effects are located after the amp model in the signal path to provide a sound similar to effects that are connected through the effects loop of an amplifier, or added at the recording console. GENRES -- Enter the main genre (music category) and as many as two sub genres for the currently active preset on the amplifier. OK -- Click OK to save all your entries for the currently active preset on the amplifier. fender. com 7 2. 0 Band Track Screens Click on the "BAND" button {A} to select a Band track and adjust Band settings. Although you cannot store Band tracks on your MustangTM amplifier like you can on the G-DEC® 3, you can play songs on your computer through Fender® FUSETM and save the associated track as part of a Mustang preset. G-DEC 3 Only Mustangs Only B. MP3 / WAVE -- Select the MP3/Wave radio button if you want to select an MP3/Wave Band track file for the currently active preset on the G-DEC 3. TRACK LIST -- Click on this drop down list to select an MP3/ Wave Band track on the G-DEC 3 hard drive (HD) or SD card on the G-DEC 3. REPEAT -- Click on this box for endless loop playback. AUDIO MIX -- Choose an audio mix for the Band track selected in the Track List {C}. Select LEFT/RIGHT MIX if you want to adjust the balance of the Band track to focus on the audio content of one channel. Select CENTER CANCEL if you want to eliminate the audio in the "center" of the mix in a stereo file. This is often effective in removing the lead guitar and vocals from a song. BALANCE -- Adjusts the left/right (1/10) balance for the Band track selected in the Track List {C} when LEFT/RIGHT MIX is chosen for the Audio Mix {E}. [. . . ] SEARCH -- Click on one or more of these buttons to highlight them as locations to search for presets and band tracks. Then type in a term in the window above and click "GO. " Your search results will be displayed below. ADD TO LIBRARY -- Click on "Add To Library" to copy preset files (*. FUSE) and band track files (*. MP3, *. WAV) and (*. MID for G-DEC 3) from anywhere on your computer to the location that FUSE searches on your computer by default. Preset list {E} to open the Preset Editor with the selected preset ready to play on the amplifier. · When you have SD Card selected as the Media location {B}, you must right-click on a preset in the Preset list {E} and first copy it to your computer before you can activate it to play on the amplifier. [. . . ]