Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual FENDER BXR 100. We hope that this FENDER BXR 100 user guide will be useful to you.
Lastmanuals help download the user guide FENDER BXR 100.
Detailed instructions for use are in the User's Guide.
[. . . ] The rugged power amplifier is designed to give years of reliable service under all conditions. It is equipped with our exclusive DELTACOMPTM adaptive compressor system. With DELTACOMPTM, it is practically impossible to clip (distort) the power amplifier. [. . . ] LOW shelving control - adjusts the low part of the frequency spectrum, where the deep "fundamentals" reside. HIGH shelving control - adjusts the high part of the frequency spectrum. Turning up the HIGH control will add "sparkle" to the sound. GRAPHIC EQUALIZER - allows precise adjustment of the tonal characteristics of the amplifier. Each control provides a 12 dB boost or cut to narrow bands of frequencies centered about 80, 150, 300, 570, 1. 1k, 2. 1k, and 4kHz. The 80, 150, and 300 Hz controls are used to adjust the low, mid, and high fundamental notes of the bass. The 570, 1. 1k, 2. 1k, and 4k controls allow control of the timbre of the instrument, allowing for a very wide variety of tonal characteristics.
J.
VOLUME control - adjusts the level of the signal coming out of the pre-amplifier section. This control is used in conjunction with the GAIN control to set the overall sound level of the amplifier. In order to maximize headroom and minimize noise, instruments with low- level pickups will require a high GAIN and low VOLUME setting, while other instruments will require a lower GAIN and higher VOLUME setting. It is recommended that the VOLUME control be set as high as possible for maximum DELTACOMPTM compressor range. PREAMP OUT jack -This jack provides an unbalanced mono output signal from the preamp. This output can be used with the POWER AMP IN jack (item L) as a patch point for mono effects devices. It can also be used to provide a signal to a recording or sound reinforcement mixer. In addition, this output can be used to drive another BXR 100 used as a slave amp. This is done by connecting a standard guitar cord from the PREAMP OUT jack of the master amplifier to the POWER AMP IN jack (item L) of the slave. POWER AMP IN jack - This unbalanced input goes directly into the power amp. It automatically disconnects the preamp when used. This jack is useful when using the effects loop feature, or when using the BXR 100 as a slave amp.
M. [. . . ] - Is the instrument properly plugged into the amplifier?(Eliminate any effect pedals and try another guitar cord. ) If, after checking all of the above, the system is still not performing correctly, consult your FENDER Service Dealer.
BXR 100 Specifications
Part Number: Type Specification: Power Requirements: 120V Version: 230V Version: PR 233 120V Version: 230V Version: 120VAC, 60 Hz, 2. 4 A Max. 22-4401 22-4461
POWER AMPLIFIER SECTION: Power output: Rated load impedance: Distortion at 100 watts: Sensitivity: Input impedance: DELTACOMPTM range: PREAMP SECTION: Input impedance: Input 1 - Greater than 420k Ohms (typically greater than 1 megaohm in the passband) Input 2 - 136k Ohms Input 1 - 13mV Input 2 - 26mV 100 watts R. M. S. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE FENDER BXR 100
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual FENDER BXR 100 will begin.
