User manual FENDER LTB PORTABLE

[. . . ] We are sure you will find your new LTB sound system to be both a unique and effective sound reinforcement product, providing years of trouble-free service. With ease of setup in mind, the integrated mixer/amplifier design combined with the full-range LTB-10 speaker enclosures makes your LTB a versatile, yet simple to operate sound system. Included in your LTB package is one dynamic cardiod microphone, one microphone cable and two speaker cables; everything you need to get started. Enclosed in a boxtop style cabinet, your LTB mixer/amplifier features individual channel preamps, +15V DC phantom power, line and mic level channel inputs, a patch bay and much, much more. [. . . ] Any signal entering this jack is mixed into the Main bus signal. FTSW - This 1/4 inch, TS, unbalanced, output jack is designed for use with an optional footswitch (P/N 048458). When a footswitch is inserted into this jack, the LTB's internal reverb can be turned on or off remotely. H I J K A. LOW - Adjusts the amount of low frequency boost or cut in the LTB. When all the tone controls are set at their 12 o'clock (notched) position, the LTB is "flat" with no frequencies cut or boosted. MID - Adjusts the amount of middle frequency boost or cut in the overall mix. HIGH - Adjusts the amount of high frequency boost or cut in the overall mix. MAIN - The main volume control of the LTB. Rotating the knob clockwise increases the LTB's overall volume level. REV - Adjusts the reverb signal level sent to the main mix. Rotating the knob clockwise increases the amount of reverb signal. REAR PANEL FUNCTIONS L L. POWER SUPPLY CORD - This is a grounding type supply cord to reduce the possibility of shock hazard. Completely unwind the cord from its cord wrap to prevent blocking air flow. Be sure to connect the cord to a grounded receptacle. PARALLEL SPKR M JACKS These speaker level output jacks feed your main speaker enclosures. LOAD TOTAL minimum impedance load is 4 ohms. Connecting a load of less than 4 ohms may result in unsatisfactory performance such as overheating to the point of thermal shutdown. 5 BASIC SETUP OF YOUR LTB Before using the LTB, please read and follow the steps listed below: 1. IMPORTANT Heed all safety warnings when operating the LTB. Please be sure to check for these items. The LTB sound system comes complete with 2 LTB-10 Speaker cabinets, 2 speaker cables, 1 microphone cable and 1 dynamic cardioid microphone. Make sure the power switch is in the OFF position, the EQ, LOW, MID and HIGH tone controls are in their 12 o'clock notched positions and all channel LEVELS, the MAIN and the REV are in their MIN positions. Volume 1 Value 2 Value 3 Value 4 Value 5 Value 6 Value 7 Value 8 Value Yes Value Stereo Cassette LEFT 9 0 2 RECORD LEVEL L R O13 124 RIGHT POWER PA U S E P L AY RECORD 2 1 3 4 -5 0 1 2 1 2 3 4 -5 0 1 2 TA P E S E L E C T NORMAL Cr O 2 M E TA L STOP REW FF This Illustration was done A Value B Value by Phil Sanchez January 27, 1997 No This full page illustration can be found on page 8. 4. Next, plug the supply cord into a power source with the correct voltage. [. . . ] If after checking all of the above the LTB is still not performing correctly, consult your nearest authorized Fender Service Center. VINYL COVERING CARE The LTB mixer and speaker cabinets are covered in vinyl for long life and lasting good looks. To clean the cabinets, use a sponge dampened with a light soapy solution. Avoid spilling any liquids on the operating surface, grilles, volume and tone controls, switches and line cord inputs. ALWAYS unplug the LTB before cleaning it or approaching it with fluids. [. . . ]