User manual FENDER REISSUE 62 ESQUIRE

[. . . ] · Only use a cart or stand with this product that is recommended by this product's manufacturer. · The power supply cord of this product should be unplugged from the outlet when left unused for a long period of time, or during electrical storms. · Do not drip nor splash liquids, nor place liquid filled containers on the unit. · CAUTION: No user serviceable parts inside, refer servicing to qualified personnel only. [. . . ] Set a custom as + modulation rate by ­ pressing TAP at least twice at the desired rate. Press TAP once for+the slowest rate possible. There is only one level setting for Phaser. ­ + ­ Modulation Effect Type Description + ­ ­ ­ ++ CHORUS Medium sweep rate with high depth + VIBRATONE ­ Fast rate with medium depth ­ LO VIB A N GE RU ­ +FLANGE ­ TREMOLO + +­ + ­ ­ + PHASER + ­ Fast rate with medium-high depth and duty cycle +­ Slow sweep rate­ with medium depth + Medium sweep rate with medium depth ­ + + ­ + ­ + ­ J. DELAY + DIGI T A ­ T APE + ­ DU + ­ ­ ­ + + Selects a Delay type and level. The level increases going clockwise within each type as illustrated from off (­), to maximum (+). Set a custom delay interval by pressing TAP at least twice at the desired rate. Press TAP once for the longest interval possible. Delay Type DIGITAL TAPE DUCKING Description 130 ms delay, single repeat (panning) 300 ms delay, low feedback, medium wow & flutter 460 ms delay, medium feedback, "ducks" out of the way when playing + ­ + DELAY C KIN G Half notes are indicated by two preset button lights. For example, A and B would light up to indicate A sharp (B flat). w w w. f e n d e r. com L K. The tuner "borrows" the preset button lights to indicate the nearest note and the capture LEDs to indicate flat, in tune, or sharp. Nearest Note Fine Tuning -40 -10 IN TUNE +10 +40 w w w. Then adjust the amplifier settings any way you like. When satisfied, press and hold any preset button for 2 seconds. Your new preset is saved in the Players' Lounge bank (assigned to the button held) and it is automatically activated. NOTE: The previous contents of the Players' Lounge preset you are saving to will be overwritten with your new preset. Effect Editing--Advanced A computer with a MIDI capable soundcard, appropriate adapters and a MIDI utility application are required for advanced effect editing. Using a computer you can edit effect parameters that are inaccessible through the Cyber­ChampTM front panel controls. Your modified effect can then be saved to a Players' Lounge preset and used in the modified form using the front panel controls (See Advanced Effect Editing on page 10). w w w. f e n d e r. com w w w. m r g e a r h e a d . net +­ + ­ +­ + ­ ­ + ­ ­ + ­ + ­ + + MIDI 9 3 MIDI MIDI IN OUT ­ + ­ + This section describes the Musical Instrument Digital Interface (MIDI) capabilities of the Cyber-ChampTM amplifier. The Cyber­ChampTM amplifier supports the MIDI standard using the MIDI IN and OUT jacks on the front panel, both 5-pin DIN jacks. The amplifier uses Channel Messages and System Exclusive Messages to accomplish the following tasks: Channel Messages See the MIDI Implementation Chart on page 14 for details. Switching Tuner and Effects On/Off You can switch the tuner on and off using MIDI program change 127 in any bank (00, 01, 02). You can switch the effects (Modulation and Delay) on and off using continuous controller 85--any value between 64 and 127 turns effects on and any value between 0 and 63 turns effects off. Reverb is not affected. See the MIDI Implementation Chart on page 14 for details. Echoing Control Changes You can control two or more Cyber­ChampTM amplifiers as one by linking their MIDI ports together. Connect MIDI OUT on the primary amplifier to MIDI IN on the auxiliary amplifier and so on down the line. [. . . ] Function ID number: 01H = Utilities Message, 02H = One Preset Message End of System Exclusive File Byte End of System Exclusive Message MIDI Dump Initiation Message VALUE F0H 08H nnH 21H 04H 23H 00H 00H 00H ddH 7BH F7H DESCRIPTION Start of System Exclusive Message Fender Manufacturer ID nn = Device ID (minus one) Amp ID number 31H. The upper nibble identifies the Cyber-ChampTM amplifier and the lower nibble designates software version. Message ID number for additional parameter controls. ID number indicating request for a MIDI Dump Unused Data Byte Unused Data Byte Unused Data Byte Dump ID byte: 01H = Transmit Utilities, 02H = Transmit One Preset End of System Exclusive File Byte End of System Exclusive Message w w w. f e n d e r. com w w w. [. . . ]