User manual FERMAX BLUETOOTH PC-PDA SOFTWARE MANUAL V1.08

[. . . ] Application user manual FERMAX BLUETOOTH PC - PDA Software version V1. 08 Code 97589I V07_10 Code 97589I, V07_10 Technical information booklet published by FERMAX ELECTRONICA S. A. E. As part of its policy of constant improvement, FERMAX ELECTRONICA S. A. E. reserves the right to modify the content of this document and the characteristics of the products referred to in it at any time and without prior notice. Any modification will be reflected in subsequent editions of this document. 2 Table of contents Prerequisites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If the PC or PDA with which you wish to configure the reader also did this the previous time, if you have the Bluetooth connection on the reader will automatically request the administrator PIN code and if it is correct will go into configuration mode. Note: it is very important, if the configuration PC is in the vicinity of the reader, to disconnect or suspend its Bluetooth interface to avoid the reader continuously requesting the administrator PIN and failing to respond to user phones while awaiting the PIN code. To return to standard operation mode, there are three alternatives: 1. With the receiver operating in configuration mode, and without needing to switch it off, press the push button we described above. The receiver goes from configuration mode into standard mode. At this moment a longer sound indicator is emitted in the buzzer than in the previous case. 2. If the receiver is in configuration mode and five minutes pass from the last configuration action executed, it will automatically switch back over to standard mode. When the application ends a command is automatically sent to the receiver which takes it out of configuration mode and back into standard mode. Find receiver Important: in order to be able to find and operate on the receiver, it must be in configuration mode. This menu enables the device to search for the receiver on which it is going to operate. To do this, it carries out a search for the available ones. When the search has ended and the device has been located, the administrator must be paired with the receiver. For this, the administration PIN is used as a pairing code (by default "4444"). If this operation is successful, a connection will be established between the two, which will enable it to operate on the destination. This action will avoid future pairings, unless certain special circumstances occur later (receiver reboot, five-minute timeout consumed, pressing the button, changing the administrator PIN). 7 Selectable receivers list. Operation information panel. 2. Find receiver menu · · The Search /More button: enables the administrator to search for the receiver. Those detected will be added to the list of selectable receivers. The Select button: enables the administrator to establish a connection between the source device and the receiver to subsequently be able to operate on it. 8 Parameters Menu 4 Parameters This menu enables the administrator to get an overall view of the receiver's operating parameters. The menu has 7 basic parameters: the operating mode, the power, the opening time (in seconds), the repeat time (the time is in tens of seconds), the management of the administrator PIN and the name of the receiver. Each one of them is totally configurable and determines the behaviour of the receiver. Operation information panel. 3. Parameters · · · · The Read BK button recovers the receiver's current operating parameters and enables them to be viewed in the different elements of the menu. The Mode drop-down menu enables us to change the current value of the operating mode. The Power drop-down menu enables us to change the current value of the power. The Opening arrows enable us to increase or reduce the value of the opening time. 9 · · · · The Repeats arrows enable us to increase or reduce the value of the repeat time. [. . . ] Important: when carrying out the action "Write BK", the list previously existing on the receiver is deleted and replaced with the application's local list. Read File The Read File operation enables us to transfer the list contained in the file to the local list of the application and thus be able to work on it. This operation will facilitate the task of applying the same list of authorised users on several receivers. To read a file, it is necessary to specify the name of the file so that this can be uploaded. This menu will also enable us to delete the existing files in the file directory. [. . . ]