User manual FERMAX MDS-BUS2 TECHNICAL MANUAL SECTION I V06-10

[. . . ] TECHNICAL MANUAL MDS - BUS2 SYSTEM Section I System Description BUS2 MDS - BUS2 US2 MDS-BUS2 TECHNICAL MANUAL The MDS-BUS2 technical manual is comprised of two sections: - Section I: Description of the MDS-BUS2 System (Code 97586I-1) - Section II: MDS-BUS2 installation diagrams (Code 97586I-2) MDS-BUS2 Technical Manual - Section I Code 97586I-1 V06_10 This technical document of an informative nature is published by FERMAX ELECTRONICA S. A. E. , who reserve the right to modify the technical characteristics of the products referred to herein at any time and without prior notice. These changes will be reflected in subsequent editions of this document. Page 2 Code 97586I-1 V06_10 BUS2 MDS - BUS2 US2 TABLE OF CONTENTS SECTION I - DESCRIPTION OF MDS-BUS2 SYSTEM MDS - BUS2 SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - Introduction: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 MDS-BUS2 DECODER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] BUS2 Bus Connector 3s off off on 3s off off 3s on on 3s off Not programmed Programmed: Guard unit does not receive calls Programmed: Guard unit receives calls Code 97586I-1 V06_10 Page 7 BUS2 MDS - BUS2 US2 MDS-BUS2 SYSTEM PROGRAMMING BUS2 Decoder Programming via the MDS Digital Panel Search name and press Enter PROGRAMMING MODE 0 Enter Code ------ AB21AB Programming Code ----- 1 Enter Programming Mode 19025 (It can be substituted for another one) Main Menu: 2 - DECODERS Programming Menu: DECODERS 2 DECODERS 1 - Individual pgm Decoders Menu: INDIVIDUAL PROGRAMMING 1 DIRECC BUS2 BB DECOD BUS2 DER BUS2 ECODE IONES R Ct V M+ -D 1 D2 2 6 PGM PGM MDS PC DL1 Press PGM button in decoder . . . Tipo A, B, C o D Audio-4: Te l e p h o n e 1 : _ _ _ _ Enter START ADDRESS: number assigned to the first To move to the terminal connected to the BUS2 Decoder. next display Enter END ADDRESS: number assigned to the last has been terminal connected to the BUS2 Decoder. 0000 if the residential terminals are programmed from the BUS2 panel. FFFF: : if the residential terminals are programmed from the general entrance. (See NOTE 3). 2 Programming BUS2 Decoder (according to type) Audio-4: Te l e p h o n e 2 : _ _ _ _ Audio-4: Te l e p h o n e 3 : _ _ _ _ Audio-4: Te l e p h o n e 4 : F F F F once the data entered, confirm pressing the "B" key B B B See NOTES Page 8 Code 97586I-1 V06_10 BUS2 MDS - BUS2 US2 Interior Block Programming under Option "C" via the MDS Digital Panel As described above there can be different types of set-up. If you choose option C, the Interior Block option should be selected via the MDS DIGITAL Panel, as detailed below. Search name and press Enter PROGRAMMING MODE 0 Enter Code ------ AB21AB Programming Code ----- 19025 (It can be substituted for another one) Main Menu: 4 - CONFIGURATION Programming Menu: CONFIGURATION 4 Configuracion 6 - MDS - City MDS-CITY 6 Press PGM button in panel . . . SKIP THIS STEP PRESS "B" B Use blocks?( B ) - Ye s . CHOOSE "YES" PRESS "B" B 6 d i g i ts C a l l ?( B ) - Ye s . CHOOSE "NO" PRESS "A" A B EXIT Code 97586I-1 V06_10 Page 9 BUS2 MDS - BUS2 US2 NOTE 1 -> DECODER Address based on the set-up type (A, B, C or D): TYPE A: features TYPE B: TYPE C: Medium Sized Blocks. TYPE D: Small Blocks: Individual Chalet or Large Blocks Residence - 199 Residences per block 9 Blocks 9 Residences per block - 99 Residences per block - 999 Blocks - 99 Blocks Start Address End Address iiii ffff iiii=ffff Audio-4: Telefono 1: _ _ _ _ Biii BBff B = Block no. Start Address BBii BBff B B = Block no. Audio-4: Telefono 2: _ _ _ _ BBBi BBBf B B B = Block no. End Address Observations: You can mix different types of set-ups within the same development but always respecting the following LIMITATIONS: a. ) - Up to - Up to - Up to - Up to b. ) 9 99 999 9999 Type B Blocks, Type C Blocks, Type D Blocks, Type A Residences, (max. Follow the steps detailed in "Programming the BUS2 Decoder" (according to type), (there is one decoder per block). Blocks 3, 4, 5, 6, 7, 8, 9 (programmed in the same way) Block 1 (45 Apartments) STEPS 1 Enter Programming mode Audio-4: Telephone 1: 0 1 0 1 Audio-4: Telephone 2: 0 1 4 5 Audio-4: Telephone 3: 0 0 0 0 Audio-4: Telephone 4: F F F F Block 2 (45 Apartments) STEPS 1 Enter Programming mode Audio-4: Telephone 1: 0 2 0 1 Audio-4: Telephone 2: 0 2 4 5 Audio-4: Telephone 3: 0 0 0 0 Audio-4: Telephone 4: F F F F . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Block 10 (45 Apartments) STEPS 1 Enter Programming mode Start Address Audio-4: 02: block no. Telephone 1: 1 0 0 1 01: starting residence no. End Address Audio-4: 02: block number Telephone 2: 1 0 4 5 45: ending residence no. 0000 -> monitor/telephone programming will be done via the ADS panel. Leave as FFFF. Audio-4: Telephone 3: 0 0 0 0 Audio-4: Telephone 4: F F F F 2 ADS Decoder Programming Block 11 (30 Apartments) STEPS 1 Enter Programming mode Audio-4: Telephone 1: 1 1 0 1 Audio-4: Telephone 2: 1 1 3 0 Audio-4: Telefono Audio-4: Telefono Block 12 (30 Apartments) STEPS 1 Enter Programming mode Audio-4: Telephone 1: 1 2 0 1 Audio-4: Telephone 2: 1 2 3 0 Audio-4: Telephone 3: 0 0 0 0 Blocks, 13, 14 and 15 (programmed in the same way) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Block 16 (30 Apartments) STEPS 1 Enter Programming mode Audio-4: Telephone 1: 1 6 0 1 Audio-4: Telephone 2: 1 6 3 0 Audio-4: Telephone 3: 0 0 0 0 Audio-4: Telephone 4: F F F F 2 ADS Decoder Programming 3: 0 0 0 0 4: F F F F Audio-4: Telephone 4: F F F F Code 97586I-1 V06_10 Page 11 BUS2 MDS - BUS2 US2 EXAMPLE 2: 230 Chalet System with a single 1 line panel on each one. Observations: - The chalets should be numbered from 1 upwards. - The residential terminals (monitors/telephones) should be programmed via the Chalet's BUS2 1 line panel. See the "Programming residential terminals via the INTERIOR BLOCK" section. - Based on the features of the system we would be in a TYPE A system --> i i i i / f f f f, (Chalets, up to 9999). Follow the steps for "Entering Programming Mode". Follow the steps detailed in "Programming the BUS2 Decoder" (according to type), (there is one decoder per block). Chalets 3 to 229 (programmed in the same way) Chalet 1 (1 House) STEPS 1 Enter Programming mode Audio-4: Te l e p h o n e 1 : 0 0 0 1 Audio-4: Te l e p h o n e 2 : 0 0 0 1 Audio-4: Te l e p h o n e 3 : 0 0 0 0 Audio-4: Te l e p h o n e 4 : F F F F Chalet 2 (1 House) STEPS 1 Enter Programming mode Audio-4: Te l e p h o n e 1 : 0 0 0 2 Audio-4: Te l e p h o n e 2 : 0 0 0 2 Audio-4: Te l e p h o n e 3 : 0 0 0 0 Audio-4: Te l e p h o n e 4 : F F F F . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Chalet 230 (1 House) STEPS 1 Enter Programming mode Audio-4: Te l e p h o n e 1 : 0 2 3 0 Audio-4: Te l e p h o n e 2 : 0 2 3 0 Audio-4: Te l e p h o n e 3 : 0 0 0 0 Audio-4: Te l e p h o n e 4 : F F F F Start Address: 2 2 ADS Decoder Programming End Address: 2 0000 -> monitor/telephone programming will be done via the ADS panel. Leave as FFFF. Page 12 Code 97586I-1 V06_10 BUS2 MDS - BUS2 US2 EXAMPLE 3: 8 block system with 115 residences each, (each block has a BUS2 panel). Observations: - The residences in each of the blocks should be numbered from 1 upwards. [. . . ] The residential terminals will not function if they have not been programmed Terminal programming is carried out in 2 steps: 1. - Terminal Programming Setup: Loft Telephone Loft Monitor Compact Loft Monitor iLoft Monitor MIC Leave the JP2 switch in place as the MAIN Panel JP2 MASTER SLAVE JP3 LEDS ON LEDS OFF CN1 PACK EXTENSION TARJETERO CN2 CARD HOLDER PAN & TILT 10 EXIT PR PR OG OG . . Press the monitor programming setup button. 2. - Allocation of Call Codes Button Panels Keypad Panels A time period of 2 minutes exists within which to carry out step 2 after terminal programming setup. Once this time has passed, the terminal will exit programming mode. Press the residence's call button Using the keypad, enter the call code and press the bell The Loft Compact and iLoft monitors have an additional function which enables monitor programming from the same monitor, without having to carry out any operation from the outdoor entry panel. It is recommended that each of the Interior Block's residences are programmed from 1 upwards. [. . . ]