User manual FESTOOL LHS 225 EQ

[. . . ] Long reach sander PLANEX LHS 225 Table of contents 1 Symbols 2 Technical data 3 Machine features 4 Intended use 5 Safety instructions 6 Commissioning 7 Machine settings 8 Operation 9 Service and maintenance 10 Accessories 11 Disposal 12 Warranty 13 EU Declaration of Conformity 14 Troubleshooting The specified illustrations are at the beginning of the Operating Instructions. Machine features Sanding head Extension pipe Handle section Abrasive Mains power cable 4 Intended use The PLANEX is designed for sanding primed drywall constructions, ceilings and walls in internal and external applications as well as removing carpet residue, coats of paint, coverings, adhesives and loose plaster. FWhen sanding large filled surfaces with high dust development, we recommend the Festool mobile dust extractor CTL/M 36 E AC PLANEX. Read all safety warnings and all instructions. [. . . ] To protect your health, wear a P2 protective mask. - Never use machines with a damaged cable. Do not touch damaged cables and pull the plug from the mains power supply if the cable becomes damaged during work. 3 Emission levels Levels determined in accordance with EN 60745 are typically: Sound pressure level 82 dB(A) Noise level 93 dB(A) Measuring uncertainty allowance K = 3 dB The emission values specified (vibration, noise) were measured in accordance with the test conditions stipulated in EN 60745 and are intended for machine comparisons. They are also used for making preliminary estimates regarding vibration and noise loads during operation. The emission values specified refer to the main applications for which the power tool is used. If the electric power tool is used for other applications, with other tools or is not maintained sufficiently prior to operation, however, the vibration and noise load may be higher when the tool is used. Take into account any machine idling times and downtimes to estimate these values more accurately for a specified time period. This may significantly reduce the load during the machine operating period. Risk of accident if the machine is operated using unauthorised voltages or frequencies. - The mains voltage and the frequency of the power source must correspond with the specifications on the machine's name plate. - In North America, only Festool machines with voltage specifications of 120 V may be used. Always pull the plug out of the socket before performing any type of work on the machine. Hold the sanding head [1-1] with the sanding pad facing downwards. If closed, release the clamping levers [2-1] and [2-2]. Slide the extension pipe [1-2] into the opening up to the stop as illustrated in [2]. Press the contact slide down until it latches into position. The noise produced during work may damage your hearing. Overall vibration levels (vector sum for three directions) measured in accordance with EN 60745: Vibration emission level (3-axis) ah < 2. FIf you wish to use the PLANEX for sanding walls in cramped spaces, for example, reduce the length of the machine by fitting the sanding head [1-1] directly to the handle section [1-3]. FWhen disassembling the machine, do not forget to press the button [3-1] to release the contact slide before opening clamping levers [2-1] and [2-2]. 2 Electronics The machine features full-wave electronics with the following properties: Smooth start-up The electronically controlled smooth start-up function ensures that the machine starts up smoothly. [. . . ] 13 EU Declaration of Conformity Long reach sander Serial no. LHS 225 EQ PLANEX 492236, 494828 Year of CE mark: 2007 We declare under sole responsibility that this product complies with the following norms or normative documents: EN 60745-1, EN 60745-2-4, EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3 in accordance with the regulations stipulated in Directive 98/37/EC (until 28 Dec. 2010 Head of Research, Development and Technical Documentation Festool GmbH Wertstraße 20 D-73240 Wendlingen REACH for Festool products, their accessories and consumables REACh is a European Chemical Directive that came into effect in 2007. As "downstream users" and product manufacturers, we are aware of our duty to provide our customers with information. [. . . ]