Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual FIELD CONTROLS 46457800. We hope that this FIELD CONTROLS 46457800 user guide will be useful to you.
Lastmanuals help download the user guide FIELD CONTROLS 46457800.
Manual abstract: user guide FIELD CONTROLS 46457800
Detailed instructions for use are in the User's Guide.
[. . . ] ITEMS INCLUDED IN KIT 1) Control box with mounted pressure switch, post purge timer and 7" vent damper cable 2) Flexible conduit connector 1) ¼" tubing connectors ITEMS NOT INCLUDED IN KIT · ¼" O. D. aluminum, copper or stainless steel tubing · Junction box with connectors and additional circuit wiring, if required DO NOT DESTROY THESE INSTRUCTIONS MUST REMAIN WITH EQUIPMENT
WARNING: INSTALLER: IF THE APPLIANCE DOES NOT HAVE A BLOCKED VENT SWITCH, A GSK-3P SPILLAGE SWITCH KIT, P/N 46458600, (NOT INCLUDED) MUST BE INSTALLED (SEE DIAGRAM B).
MOUNTING CONTROL BOX The control box must be mounted within 6' of the vent damper, and within reach of the appliance's existing damper cable. If the control box must be mounted out of reach of the power venter's attached wiring, an additional installer supplied junction box and wiring (with approves wiring enclosure if necessary) will be required. [. . . ] The wiring should be protected by an overcurrent circuit device rated at 15 amperes. CAUTION must be taken to ensure that the wiring does not come into contact with any heat source. All line voltage and safety control circuits, between the venter and the appliance, MUST be wired in accordance with the National Electrical Code for class one wiring or equivalent methods. Route the venter motor and control wiring with an appropriate wiring method. LOW VOLTAGE WIRING INSTRUCTIONS FOR BOILERS: 1. Route the appliance's vent damper cable to the CK-41P. Plug the cable into the receptacle located inside the CK41P using the supplied plastic knockout grommet (if the cable does not have a conduit connector). (See Diagram A) Connect the CK-41P's pre-wired damper cable to the vent damper (See Diagram A). Snap the end of the flexible conduit into place on the vent damper conduit bracket.
LINE VOLTAGE WIRING INSTRUCTIONS: 1. Verify that the circuit to be supplying power to the CK-41P is disconnected. Connect the CK-41P green grounding wire to the circuit's ground wire. Verify that the control box is properly grounded. Connect 120 volts hot power source wire to terminal L1 on CK-41P. Connect 120 volts neutral power source wire and white wire from venter motor to terminal N on the CK-41P. [. . . ] Make sure the vent damper is in open position. Check for 24 volts from both yellow wires on pressure switch to black wire on base of timer relay. If neither yellow wire has 24 volts, the vent damper is defective, has loose wiring, or is not receiving call for heat on the orange wire. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE FIELD CONTROLS 46457800
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual FIELD CONTROLS 46457800 will begin.
