User manual FIRST ALERT FA148CP-CN

[. . . ] )$&)$&&1 )$&3)$&3&1 6HFXULW\6\VWHPV 8VHU·V*XLGH R K5309-5 7/01 1 IMPORTANT! PROPER INTRUSION PROTECTION For proper intrusion coverage, sensors should be located at every possible point of entry to a home or commercial premises. This would include any skylights that may be present, and the upper windows in a multi-level building. In addition, we recommend that radio backup be used in a security system so that alarm signals can still be sent to the Central Monitoring Station in the event that the telephone lines are out of order (alarm signals are normally sent over the phone lines). EARLY WARNING FIRE DETECTION Early warning fire detection is important in a home. Smoke and heat detectors have played a key role in reducing fire deaths in the United States. [. . . ] This code is typically assigned to someone (e. g. , babysitter or cleaner) who has a need to arm/disarm the system only at certain times. The user of this code should not use the "Quick Arming" feature. Intended for use when you are forced to disarm or arm the system under threat. When used, the system will act normally, but can silently notify the Central Monitoring Station of your situation, if that service has been provided. (FA168C) Can do everything a standard user can do, and can assign user codes to users in their partition. 0 1 2 Standard User Arm Only Guest 3 Duress Code 4 Partition Master ­ 28 ­ 6HFXULW\&RGHV$XWKRULW\/HYHOV&RQW +RZWR$VVLJQ8VHU&RGHVDQG$WWULEXWHV The following lists the various command strings for adding user codes and attributes. Refer to the User Setup chart at the back of this manual for factory assignments of user attributes and to keep a record of user programming. NOTE: Partition Master codes (FA168C only) apply only to those user numbers previously assigned (by the system master/installer) to the partition master's partition. Add User Code: (Users 03/33 are preset to partition programmers, but can be changed. ) System/Partition Master code + [8] + user no. + new user's code User 01 = installer User 03 = partition 1 master User 02 = master User 33 = partition 2 master The Keypad beeps once to confirm that new user was added. System/Partition Master code + [8] + [user no. ] + [#] [0] The user code and all attributes* programmed for this user number, including any associated RF keys, are erased from the system. (*except assigned partition) System/Partition Master code + [8] + [user no. ] + [#] [1]+ auth. level Authority Levels (see definitions on previous page): 0 = standard user 3 = duress 1 = arm only 4 = partition master (FA168C only) 2 = guest System/Partition Master Code + [8] + [user no. ] + [#] [2]+ group (1-8) You can assign users to a group, then set an access schedule that defines the times this group of users can operate the system. The system ignores these users outside the scheduled times. System Master Code + [8] + [user no. ] + [#] [3] + [0] + partition(s) + [#] This command assigns the partitions the user can access. If more than one, enter partition numbers sequentially, then press [#] to end. E. g. , master code + [8] + [user no. ] + [#] [3] + [0] + [1] [2] + [#] gives the user access to partitions 1 and 2 and the common partition. Partition Entries: 1 = partition 1 and common 2 = partition 2 and common 3 = common partition only Master/Part. Code + [8] + [user no. ] + [#] [4]+ zone no. Use this command to assign a wireless button device (keyfob) to this user (keyfob must be enrolled in system first; see installer). Zone number: enter the zone number assigned to a button on the keyfob that will be used for arming/disarming by this user. Code + [8] + [user no. ] + [#] [5] + 0 or 1 You can program a user so that a message is sent to a pager whenever this code is used to arm or disarm the system. Paging On/Off: 1 = allow paging; 0 = no paging for this user Delete User Code: Authority Level: Factory Assignments: users 04-32/34-49 = 0 users 03/33 = 4 Access Group: Factory Assignments: none User's Partition: (FA168C only) Factory Assignments: Part. [. . . ] In the case of a monitored alarm system, authorities may not respond appropriately. · This equipment, like other electrical devices, is subject to component failure. Even though this equipment is designed to last as long as 10 years, the electronic components could fail at any time. The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance. [. . . ]