User manual FISHMAN ACOUSTIC MONITOR PRO

[. . . ] Always replace the line cord (AC mains supply) with the same type and rating. Always turn off the amplifier before making or unplugging any AC connections. Do not operate this amplifier in the rain or where excessive moisture is present. Never operate it with your ear in front of the speaker. Please fill in the following information for future reference: MODEL NUMBER: SERIAL NUMBER: DEALER'S NAME: DEALER'S ADDRESS: DATE OF PURCHASE: 2 A C O U S T I C M O N I T O R P R O F R O N T PA N E L F E AT U R E S 1) CLIPPING INDICATOR (See Page 4) 2) VOLUME LEVEL (See Page 4) 3) POWER INDICATOR (See Page 4) R E A R PA N E L F E AT U R E S 1) TWEETER LEVEL (See Page 5) 2) BASS EXTEND (See Page 5) 3) GROUND LIFT (See Page 6) 4) BALANCED OUTPUT (See Page 6) 5) UNBALANCED OUTPUT (See Page 6) 6) VOLTAGE SELECT (See Page 7) 7) POWER SWITCH (See Page 7) 8) FUSE HOLDER (See Page 7) 9) AC RECEPTACLE (See Page 7) 10) UNBALANCED INPUT (See Page 6) 11) BALANCED INPUT (See Page 6) 12) ROOM COMPENSATION SWITCH (See Page 5) 13) STEREO TAPE / CD INPUT (See Page 5) ACOUSTIC MONITOR PRO OWNER'S MANUAL 3 A C O U S T I C M O N I T O R P R O OPERATING INSTRUCTIONS - FRONT PANEL CLIP LED This LED glows only when incoming signal levels from an instrument exceed the point at which the buffer amplifier or power amp distorts, a sure sign that the signal level is too "hot. " Adjust the volume on your instrument or preamp so that the Clip LED only glows when you whack your instrument's strings exceptionally hard. LEVEL This knob controls the volume being sent from the Input Stage to the Power Amp of the Acoustic Monitor Pro. [. . . ] NOTE: The signal from the Send jack is electronically buffered, meaning that it is designed to drive other gear without a degradation in the tone and overall signal quality. Its output strength is not affected by the Level control. IN (XLR) This electrically balanced XLR input is designed to accept low- impedance microphones or prolevel sound sources. It will also accept a signal from the XLR output of the Acoustic Performer Pro. OUT (1/4") This output is useful for sending a signal to battery-powered devices sucha as electronic tuners or portable tape recorders. It is NOT recommended for use in "daisy-chaining" a series of Monitors or sending signals to non-battery-powered devices as this may result in a ground loop. IN (1/4") This input will accept line-level signals from a range of sound sources including piezo and magnetic pickups. It will also accept a signal from the Effects Send output of the Acoustic Performer Pro. However, a preamp is recommended for better control of your sound. 6 A C O U S T I C M O N I T O R P R O OPERATING INSTRUCTIONS - POWER SECTION VOLTAGE SELECTOR The Voltage Selector switch provides the option of powering the Acoustic Monitor Pro with either 115 volts AC or 230 volts AC. You must use a cord with the appropriate plug configuration for the AC (mains) receptacles in the area in which you use it. If you are taking the Acoustic Monitor Pro overseas, check with your dealer regarding the appropriate cord and plug configuration, or contact Fishman Customer Service. IMPORTANT: When operating in the United States, always set the Voltage Selection switch for 115V using a 5 Amp Slow Blow Fuse. In Europe, set for 230V with a 2. 5 Amp Slow Blow Fuse. ON/OFF SWITCH The Acoustic Monitor Pro's On/Off Switch has a "I" symbol for on and a "0" symbol for off. Always turn the Acoustic Monitor Pro off before unplugging it. AC POWER RECEPTACLE Plug your AC (mains) power cord into this receptacle and the other end into a grounded outlet. Do not cut off the grounding pin, and never use a 3-pin-to-2pin adapter unless you ground the adapter's grounding tab. If you use an extension cord, always use a heavy-duty cord that is no longer than necessary. NOTE: If your AC (mains) cord is ever damaged or lost, replace it only with the same type. CHANGING THE FUSE The Fuse Holder is located to the left of the AC Receptacle (See Page 3, Item #9). Insert a small screwdriver into the small notch on the side of the Fuse Holder to remove it from the AC Receptacle. After replacing the fuse, slide the Fuse Holder all the way into the Back Panel until it snaps into place. ACOUSTIC MONITOR PRO OWNER'S MANUAL 7 A C O U S T I C M O N I T O R P R O INTERFACING THE ACOUSTIC MONITOR PRO WITH OTHER GEAR 1) PLAYING AN INSTRUMENT: The Acoustic Monitor Pro has a 1/4" input jack that will accept line-level signals. However, a preamp or equalizer is recommended (such as the Fishman Acoustic Blender, Model G, Pro-EQ or Dual Parametric D. I. ) for better control of your sound. 2) USING THE OUTPUTS: The Acoustic Monitor Pro can send a signal via the Balanced XLR OUT to a mixing board, recording console or to the Balanced XLR IN of an additional Acoustic Monitor Pro. The Unbalanced 1/4" OUT is NOT recommended for this application. It is best for sending a signal to batterypowered devices such as electronic tuners or portable tape recorders. 8 A C O U S T I C M O N I T O R P R O 3) INTERFACING WITH THE ACOUSTIC PERFORMER PRO: The Acoustic Monitor Pro is the perfect companion to FISHMAN's Acoustic Performer Pro amplifier. When using an Acoustic Performer Pro you may want to send your signal to an Acoustic Monitor Pro for additional sound reinforcement. You can do this by connecting one of the Balanced XLR Sends of the Performer to the Balanced XLR IN of the Monitor. You can also send a Balanced signal from the Monitor's XLR OUT to a Mixing Board or PA System. POSITIONING THE ACOUSTIC MONITOR PRO The Acoustic Monitor Pro's unique design makes it ideal to be used three different ways: standing upright, lying on its side, or supported on a stand. [. . . ] This warranty does not cover units used for loan or rental. Limitation of liability: the above warranty represents the purchaser's exclusive remedy and FISHMAN shall not be liable for any special, incidental, or consequential damages or expenses relating to the product sold. Some states do not allow limitations on the duration of implied warranty or the exclusion may not apply to some purchasers. This warranty gives the purchaser specific legal rights and the purchaser may also have other rights which vary from state to state. RETURN POLICY To return products to FISHMAN TRANSDUCERS, you must follow these steps. . . [. . . ]