Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual FISHMAN ELLIPSE BLEND. We hope that this FISHMAN ELLIPSE BLEND user guide will be useful to you.
Lastmanuals help download the user guide FISHMAN ELLIPSE BLEND.
Detailed instructions for use are in the User's Guide.
[. . . ] Installation Guide
Installation
WARNING!Installation of the Ellipse Blend is to be performed only by a professional repairperson. [. . . ] Remove the components from the endpin preamp as indicated
Remove Capacitor Remove Resistor "182"
000 182
Requirements
The Ellipse Blend is compatible with the following active pickup systems: · Fishman Acoustic Matrix Natural I & II - Revision 4. 0 or higher · Fishman Powerjack - Revision 2. 3 or higher · Martin Gold Plus- Revision 4. 0 or higher · Martin Active Jack - Revision 2. 3 or higher
2. Solder the new 2k resistor (supplied with your Ellipse Blend) to the preamp circuit board
2k Resistor "202"
202 000
Note that Revision numbers for each pickup are printed on the preamp circuit board inside the endpin jack. Note: Do not use with the discontinued Acoustic Matrix Natural or the Acoustic Matrix Hot preamps or older revisions of the Martin Gold Plus systems. These units can be identified by the rectangular metal box that encases the electronics.
3. Thread the Ellipse Blend cable through the preamp barrel and solder to the preamp circuit board
Shield Black
Red White
202 000
White
*Taylor guitars with NT neck or Larrivee guitars.
Fishman Powerjack, Martin Active Jack - Rev 2. 3 1. Remove the "000" jumper from the endpin preamp.
Remove Jumper "000"
000
We include two adhesive backed clips to help you secure the wires to the side of the guitar. A cable tie is also included to bundle the wires together and provide strain relief where the wires exit the endpin preamp. Once the wires are secure inside the guitar, the Ellipse Blend will easily snap in place on top of the magnetic base
2. Thread the Ellipse Blend cable through the preamp barrel and solder to the preamp circuit board
Red Shield Black
Microphone Positioning
You can position the microphone to find the "sweet spot" inside the instrument. Take the time to experiment with microphone placement until you find the position that works best in the instrument.
White White
Less Bass
More Bass
Location
Locate the Ellipse Blend flush on the edge of the soundhole below the bass strings. When properly aligned, the module will be centered between the transverse brace above the soundhole and the X-brace.
Plug in the guitar and move the blend slider to the left for mic only. Start with the mic capsule so that it faces the back of the guitar. Move the mic closer to the sound hole for more bass. Turn the capsule toward the sides of the instrument for less bass.
Transverse Brace
Microphone Trim Control
A small circular potentiometer is recessed below the volume slider and can be accessed with a small slotted screwdriver. [. . . ] Re-install the endpin jack.
Your satisfaction is very important to us. If you have any questions, please contact Fishman Service and Support at www. fishman. com
www. fishman. com
514-000-009 · Rev A · 6-15-04
Volume
Mic Trim [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE FISHMAN ELLIPSE BLEND
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual FISHMAN ELLIPSE BLEND will begin.