User manual FLAM ELEGANZA 44-95 DIMENSIONS

[. . . ] Mention of software products manufactured by other companies does not necessarily constitute endorsement by the manufacturer . While all reasonable efforts have been made to make this document as accurate and helpful as possible, we make no warranty of any kind, expressed or implied, as to the accuracy or completeness of the information contained herein. The most up-to-date drivers and manuals are available from the web site: http://www. okiprintingsolutions. com Trademark Information _______________________________ Oki and Oki Printing Solutions are registered trademarks of Oki Electric Industry Company Ltd. Adobe and PostScript are registered trademarks of Adobe Systems. [. . . ] > Ethernet ­ For network cable connection. NOTE Interface cables are not supplied with your printer. MPS9650c User's Guide> 46 CONNECTING THE PARALLEL INTERFACE 1. Connect a parallel cable between the printer and computer. 3. Turn on the printer and then the computer. CONNECTING THE USB INTERFACE Do not connect the USB cable at this time. You will be instructed when to connect the USB cable when you run the Drivers CD. If you are connecting your printer directly to a stand alone computer proceed to the section entitled "Printer Drivers". MPS9650c User's Guide> 47 CONNECTING THE NETWORK INTERFACE CAUTION! Do not connect a USB cable into the network interface connector as this may lead to malfunction. Install the Ferrite core to the Ethernet cable as shown. MPS9650c User's Guide> 48 3. Connect an Ethernet cable between the printer and an Ethernet hub. 4. Turn on the printer and then the computer. If your printer is to be installed as a network printer, please refer to the relevant section in the Software Installation Guide and Configuration Guide for further details on how to configure the network connection before installing the printer drivers. NOTE Administrator's authority is required when installing a network connection. USING THE DRIVERS CD Insert the Printer Software CD into your computer and follow the onscreen instructions. You are prompted to follow a set of basic steps to configure the display panel language, install drivers and other software and finally print a test page to check that your printer is operating correctly. MPS9650c User's Guide> 49 OPERATION USING THE PRINTER For full details of how to use the printer and any optional accessories to print jobs efficiently and effectively, please refer to the Printing Guide. MPS9650c User's Guide> 50 CONSUMABLES AND MAINTENANCE This section explains how to replace consumable and maintenance items when due. As a guide, the life expectancy of these items is: > Black Toner -- 18, 500 Letter pages at 5% coverage. > Cyan, Magenta, Yellow Toner-- 16, 500 Letter pages at 5% coverage The printer is shipped with sufficient toner for 7, 500 Letter pages in the print cartridges of which 1 ­ 2, 000 Letter pages of toner are used to charge the image drum. > Image drum -- 42, 000 Letter pages average life > Transfer belt -- Approximately 100, 000 Letter pages > Fuser -- Approximately 100, 000 Letter pages > Waste toner -- 30, 000 Letter pages average life CHECKING CONSUMABLE/MAINTENANCE ITEM USAGE At any time, you can check how much of each consumable/ maintenance item is left by using the appropriate menus. For example, enter the menu system and follow the path: Configuration>Supplies Life>Cyan Toner The percentage of Cyan Toner remaining is displayed on the display panel and the printer then returns to the ready to print status. REPLACEMENT INDICATIONS The display panel provides messages to the effect that consumables/maintenance items are running low or nearing end of life followed some time later by a message that replacement is required. You should replace the item as soon as possible after this message is displayed to avoid the possibility of print quality being compromised. In this example Tray 1 is used, the procedure being similar for all other trays. MPS9650c User's Guide> 65 1. Squeeze the catch (1) on Tray 1 side cover and open the cover. 2. Holding it by the tab (2), turn the paper guide outward. 2 3. Carefully remove the jammed paper. MPS9650c User's Guide> 66 4. Put the paper guide back into position and close Tray 1 side cover. OPEN COVER, PAPER JAM, SIDE COVER 1. If the MP Tray is open, close it so that the side cover (1) is visible. 1 MPS9650c User's Guide> 67 2. Pull the release lever (2) and pull open the side cover. 2 3. Carefully remove the jammed paper. MPS9650c User's Guide> 68 4. Close the side cover. OPEN COVER, PAPER JAM, TOP COVER 1. Squeeze the top cover handle (1) and open the top cover. 1 WARNING! Be careful not to touch the fuser unit which is hot after printing. MPS9650c User's Guide> 69 2. Squeeze the basket handle (2) and raise the drum basket. 2 3. Carefully remove any paper on the belt. 4. If paper is jammed in the fuser unit, push the lock lever (3) in the direction shown to release the unit. WARNING! Be careful not to touch the fuser unit which may be hot after printing. If the fuser unit is hot, wait until it cools before attempting to remove any jammed paper. MPS9650c User's Guide> 70 Holding the fuser unit (4) by the handle, lift it out of the printer and place it on a flat surface. 4 3 5. Pull up the jam release levers (5) and remove the jammed paper. 5 MPS9650c User's Guide> 71 6. Carefully replace the fuser unit into the printer and turn the lock lever (6) in the direction shown to lock the fuser unit. 6 7. If paper is jammed near the paper exit, open the face-up stacker (7). 7 MPS9650c User's Guide> 72 8. Open the side cover (paper exit) (8) and remove the jammed paper. 8 9. Close the side cover (paper exit) and then the face-up stacker. MPS9650c User's Guide> 73 10. Return the image drum basket (9) into position and check it is locked. 9 11. Close the top cover and ensure it is latched. MPS9650c User's Guide> 74 PAPER JAMS ­ DUPLEX UNIT (IF INSTALLED) CHECK DUPLEX UNIT, PAPER JAM 1. If a Finisher unit is attached to your printer, operate the lever (1) of the Inverter unit to separate the Inverter from the printer. 1 2. Operate the duplex cover release button (2) and open the cover. 2 MPS9650c User's Guide> 75 3. Carefully remove any jammed paper. 4. Operate the levers (3) and pull out the duplex unit. 3 3 MPS9650c User's Guide> 76 5. Holding the front top cover by the grip (4), push it gently inwards and raise it. 4 6. Remove any jammed paper. MPS9650c User's Guide> 77 7. In similar manner, check for and clear any paper jammed under the rear top cover. 8. Replace the two top covers. MPS9650c User's Guide> 78 9. Raise the front cover of the duplex unit. 10. Push the duplex unit back into position. MPS9650c User's Guide> 79 11. If you detached a Finisher unit to gain access to the duplex unit, replace the Finisher unit. MPS9650c User's Guide> 80 PAPER JAMS ­ FINISHER (OPTIONAL ACCESSORY) CHECK FINISHER, PAPER JAM/PAPER REMAINS Use the Help button on the printer control panel to check the number displayed. You will need this to be able to clear the paper jam. The following paragraphs explain what to do for each of the indicated numeric codes. 591, 592, 593, 599/ 643, 645 (PAPER JAM AROUND FINISHER) 1. Remove any paper at the Finisher paper exit. MPS9650c User's Guide> 81 2. Operate the Finisher lever (1) and move the Finisher away from the Inverter. 1 3. Open the Finisher top cover. MPS9650c User's Guide> 82 4. Carefully remove any jammed paper. 5. Close the Finisher top cover. 6. Move the Finisher back into position and connect it to the Inverter. MPS9650c User's Guide> 83 594, 597, 598/ 644, 646 (PAPER JAM IN FINISHER) 1. Operate the Finisher lever (1) and move the Finisher away from the Inverter. 1 2. Open the Finisher front cover (2). 2 MPS9650c User's Guide> 84 3. Continue to turn the lower knob (3) clockwise until any jammed paper is completely ejected. 3 4. [. . . ] Ensure that the display panel indicates that the printer is ready to print. Enter menu mode by pressing either the Up-arrow or Down-arrow button and press them repeatedly until the Menus menu is highlighted. Press the Enter button to select this menu. Press the Up-arrow or Down-arrow buttons repeatedly until Tray Configuration is highlighted. MPS9650c User's Guide> 124 3. [. . . ]