User manual FLAM GMT 68-57 DIMENSIONS

[. . . ] Written and produced by the Oki Data Training & Publications Department. Please address any comments on this publication · by mail to: Training & Publications Department Oki Data Americas, Inc. Laurel, NJ 08054-4620 · or by email to: pubs@okidata. com We welcome you to visit our web site: http://www. okidata. com FLAM is a registered trademarks/marques déposées/marcas registradas, and FLAMCOLOR and FLAMcare are trademarks of Oki Electric Industry Company, Ltd. Adobe, Acrobat, Acrobat Reader, Illustrator, PageMaker, Photoshop, PostScript and Type Manager are trademarks of Adobe Systems Inc. , which may be registered in certain jurisdictions. [. . . ] CHANGE DRUM [color] CHANGE DRUM displays and the corresponding color indicator blinks when an image drum needs changing and the toner is low. You can recover temporarily by opening and closing the cover, but CHANGE DRUM will continue to display after printing every 20 pages until a new drum is installed. How to Replace an Image Drum Each image drum, toner cartridge, and slot in the printer has a label marked with its corresponding color. Caution! Extended exposure to light can temporarily damage the image drums. Do not open the printer until you are ready to install the toner cartridge. 1 Turn the printer off and wait for the fuser to cool down. Warning! High temperature; allow at least 20 minutes for parts in this area to cool before handling. 2 Press the OPEN button and lift the cover. 24 | FLAMCOLOR 8 3 Lift the image drum, with toner installed, out of the printer. Discard both in accordance with local regulations. 6 Loosen all the tape holding the foam shipping insert, then carefully remove the insert (there is toner on the bottom of the insert--be careful not to spill it!). 4 Close the printer cover. Caution! To avoid damage to the drum, do not touch the shiny green surface. 5 Unwrap the new image drum, but leave the protective paper (1) in place. 7 Remove the new toner cartridge from the packaging and shake it from side to side a few times to distribute the toner evenly. Handy Reference | 25 8 Peel the tape off the bottom of the cartridge. 10 Lower the right side of the cartridge, aligning the slot with the ridge in the image drum, then push the colored lock lever back until it stops. 9 Insert the left end of the toner cartridge into the toner well, placing the recess in the end of the cartridge under the tab on the image drum. 11 Remove the protective paper from the image drum. 26 | FLAMCOLOR 8 12 Open the printer cover and insert the new image drum cartridge, matching the color-coded labels on the image drum and in the printer. 14 Close the printer cover, pressing down to lock it in place. 13 Open the LED Lens Cleaner supplied with the toner cartridge and use it to clean the LED arrays located on the underside of the cover. 15 Reset the Drum Counter: a Press ON LINE, then press and hold Menu 2 until COLOR REG ADJUST appears on the display. b Press Menu 2 repeatedly until ENGINE CNT RESET appears. The message CYAN DRMCNT RESET appears. d If necessary, press Menu 2 repeatedly until the message corresponding to the drum you are replacing appears. RESETTING briefly appears on the display. To set the color registration: 1 Make sure the printer is off line (press ON LINE to place the printer off line). 2 Press and hold Menu 2 until COLOR REG ADJUST appears on the display. 3 Press ENTER. The printer prints a color test page with 9 sections, each with a series of lined boxes in it. Lined Boxes Lined Box Numbers Section #1 List Box 32 | FLAMCOLOR 8 4 Beginning with section #1, find the lined box where no color shows in the spaces between the black lines and note its corresponding number. ! If more than one box has no color, select the one closest to zero. If all the boxes have color, select the lightest one, nearest zero. 7 Repeat steps 5 and 6 for each of the remaining seven sections. If you need to go back, hold Menu 2 down to move backwards through the menu. 8 When you are satisfied with your selections, press Menu 2 repeatedly until PRINT EXECUTE appears on the display. The printer prints another color test page. This time, the box where no color shows should correspond to box +1, 0, or -1 for each section. If it doesn't, press Menu 2 and repeat steps 4 through 9 until it does. 10 Press ON LINE to save the settings and exit the menu. 5 The display reads ADJUST #1, with the number 0 on the second line. Press to increase the number or to decrease it, until the second line reads the number of the correct box for section #1. [. . . ] If this does not clear it, make a note of the error message, and contact your authorized Oki Data service dealer. When data is sent to the printer, it automatically warms up briefly before printing. If you want to disable or change this setting: 4 Press ENTER to set the selection as the default. An asterisk (*) appears to indicate the new default setting. [. . . ]