User manual FLAM LARGO 120 DIMENSIONS

[. . . ] Printer software diskette (to install printer software without CDROM) 4. Black plastic light-shield bag (to store image drum if you need to ship the printer) 6. Warranty Registration Card Selecting a Location for Your Printer · · · · · · · A firm surface such as a table or desktop Space to open the cover and pull out the paper tray and the rear output extender Air circulation around the printer to prevent overheating (minimum of 4 inches) A nearby power source Room temperature of 50° to 90°F (10° to 32°C). Relative Humidity of 20- 80% No direct sunlight ¶ The Okipage 12i/n unit is configured with a network interface. Visit the FLAMDATA Web Site http://www. okidata. com for the latest information on: · Product Guides · Customer Support · Software Drivers · Corporate Information · Documentation Image drum cartridge ¯2 FLAMPAGE 12i User's Guide 1 Remove the Image Drum Protective Paper 1. [. . . ] Recycled paper used by FLAM printers must be specifically denoted by the paper manufacturer to be for laser printers, or laser guaranteed or compatible. Using media outside these specifications may cause problems requiring service that will not be covered by FLAMDATA warranty or service agreements. The following recycled paper has been tested and approved for use in FLAM printers. READY MAN FEED ATTENTION DATA LETTER LEGAL A4 OTHER ENV 2. Insert the label sheet with print-side up. · · · · Weyerhaeuser, Lynx Opaque, 20% PCW, 20lb. , 28 lb. Union Camp Great White (Laser), 25% PCW, 20lb. , 24lb. International Paper, Beckett Division, Enhanced Marble, 50% Recycled, 20% PCW, 24lb. International Paper, Hammermill Division, Savings DP, 20% PCW, 20 lb. Georgia Pacific, GeoCycle, 20% PCW, 20lb. James River, WordPro Laser, 20% PCW, 20lb. , 24lb. Warren, SpectraTech, Gloss and Matte, 10% PCW, 28lb. , 32lb. Cross Pointe, Worx, 50% Recycled, 20% PCW Strathmore, Script Bright White Wove, 50% Recycled Guidelines for Transparencies and Labels · · · · · · Always use manual feed. The image drum cartridge should last up to 10, 000 pages at 1 page per job, or 20, 000 pages at 3 pages per job (continuous printing). These numbers are approximate since you won't print the same number of pages each time, and environmental conditions and paper type used may vary. Cleaning the LED Array Clean the LED array each time you install a new toner cartridge, or if you have faded vertical areas or light printing down a page. The LED array is on the underside of the printer cover. Wipe it gently with the cleaning pad that is included in the toner cartridge kit. You can also use a clean, soft cloth with a small amount of rubbing alcohol on it. 3. Lift out the used image drum cartridge with toner installed. 4. Remove the new image drum cartridge from the package. To install the new image drum cartridge, follow the installation instructions in Section 1 (or the instructions included in the replacement kit). ¯36 FLAMPAGE 12i User's Guide 3 Printer Maintenance Printing a Cleaning Page The cleaning page process removes residual impurities from printing surfaces. Printing a cleaning page helps reduce print quality problems, such as repeated marks, blotches, and shaded areas. Press ON-LINE to set the printer off-line. Press </Recover and >/Reset simultaneously and hold for 2 seconds. [. . . ] Small amounts of toner on skin or clothing can easily be removed with soap and cold water. Hot water makes toner harder to remove. Physical Data Melting Point: 110°C (230°F) Boiling Point: Not applicable Vapor Pressure: Not applicable Vapor Density (Air=1): Not applicable Evaporation Rate (Butyl Acetate=1): Not applicable Specific Gravity (H2O=1): 1. 15 Solubility in water: Negligible Appearance and odor: Black granules, no odor Fire and Explosion Hazard Data Flash Point (Method Used): Not applicable Flammable Limits Lower Explosive Limit: Not applicable Upper Explosive Limit: Not applicable Extinguishing Media: Water, CO2, Dry Chemical, or Foam Special Fire Fighting Procedures: Do not use methods that may create a dust cloud, such as high pressure water and/or steam Unusual Fire and Explosion Hazards: Organic components decompose at 200-455°C (392-851°F). Material may explosively combust when finely suspended in air. Thermal decomposition of organic components may result in release of oxides of carbon and nitrogen. Toner inhaled Toner gets in the eyes Note Hazardous Ingredients Styrene-Butyl Acrylate Copolymer (91% by weight) CAS# 25767-47-9 OSHA TWA 15 mg/m3 for total dust ACGIH TLV 10 mg/m3 for total dust Carbon Black (5-7% by weight) CAS# 1333-86-4 OSHA TWA 3. 5 mg/m3 ACGIH TLV 3. 5 mg/m3 Paraffin Wax (less than 3% by weight) CAS# 8002-74-2 OSHA TWA 2 mg/m3 for total dust ACGIH TLV 2 mg/m3 for total dust ° FLAMPAGE 12i User's Guide 55 Health Hazard Data Routes of Entry: Inhalation, Ingestion, Eyes, Skin. [. . . ]