User manual FLAM MT 44-120 DIMENSIONS

[. . . ] Written and produced by the Okidata Training & Publications Department. Please address any comments on this publication by mail to: Training & Publications Dept. Laurel, NJ 08054-4620 or by email to: pubs@okidata. com For the latest product information, printer drivers, manuals, special offers, etc. , we welcome you to visit our multilingual web site: http://www. okidata. com. FLAM and Okidata are registered trademarks/marques déposées/marcas registradas, and OkiLAN is a trademark, of Oki Electric Industry Company, Ltd. Adobe and PostScript are trademarks of Adobe Systems Inc. [. . . ] 2 Attach one end of the cable to the Ethernet (RJ45) connector on the OkiLAN Print Server. 3 Insert the opposite end into the RJ45 port on the network card to which the Macintosh is connected. 4 Turn the printer and the Macintosh back on. Quick Start | E-19 5 Overview Load Paper !! For detailed information on usable print media, see Print Media in the User's Guide. Loading Paper 1 Pull out Tray 1. The Paper Tray (Tray 1) The paper tray takes 530 sheets of 20-lb (75 g/m2) paper. Print media (including ink on preprinted forms) must be able to withstand 392°F (200°C) for 0. 1 second. E-20 | Quick Start 2 Adjust the guides to fit the paper. 4 Load Tray 1. ! 3 Fan the paper. Make sure paper is below tabs (1) on either side. Do not fill above PAPER FULL marks. Quick Start | E-21 5 Reinsert the tray until it locks in place. Selecting Paper Size & Media Type Factory settings: Paper Size: automatically determined by position of paper tray guides Media Type: optimized for printing on 20-lb. (75 g/m2) paper If you are consistently using another type of media in the paper tray, you can change the setting to match what you are using: see Changing Media Type for Tray 1 under Printer Menus in the Printer Control section of the User's Guide. · The Paper Tray Gauge The paper tray gauge indicates the amount of paper left in Tray 1, eliminating the need to open the tray to check. E-22 | Quick Start · The Front Feeder Printing Using the Front Feeder 1 In your software program: a Enter the printer setup menu. c Select the media type, size and orientation. !! · · · · When you are done printing using the Front Feeder, re-enter the printer driver and change the Paper Tray setting back to the previous setting (normally Tray 1). 2 Lower the Front Feeder. Print media (including ink on preprinted forms) must be able to withstand 392°F (200°C) for 0. 1 second. Use the Front Feeder for the following types of media: Standard paper Envelopes Labels Transparencies Card stock (up to 36 lb, 105 g/m2) · Quick Start | E-23 3 Flip out the tray. 5 Adjust the paper width guides. 4 Pivot out the extender. E-24 | Quick Start 6 Load the print media. Standard Paper Envelopes · Face up; insert letterhead with top edge nosed into printer. Use Top or Rear exit. Return address on lower left side; flap underneath Use Rear exit only. 7 Follow the on-screen instructions to complete the installation. 8 Print a test page: a Click Start on the Windows taskbar, then select Settings Printers. b Click the MT 44-120 printer icon with the right mouse button, then select Properties. c Click Print Test Page on the General tab. E-36 | Quick Start ® ! These instructions assume that D is your CD-ROM drive. Running the Electronic Registration Program 1 Click Start on the Windows taskbar. 3 From the submenu, click MT 44-120 On-Line Registration. 4 Follow the on-screen instructions. ® Installation for Windows 3. 1x ! 1 2 3 4 5 These instructions assume that D is your CD-ROM drive. Insert CD in CD-ROM drive. Wait for the FLAM Menu Installer Setup window to appear. 6 Click Typical or Custom, depending on which components you wish to install. 7 Follow the on-screen instructions to complete the installation. 8 Print a test page: open Windows Notepad, type in a few words, then print the document. Running the Electronic Registration Program 1 Double-click the MT 44-120 program group from the Program Manager. 2 Double-click the MT 44-120 On-Line Registration icon. [. . . ] 5 Follow the instructions on your screen to complete the process. E-38 | Quick Start Uninstalling the Software For information on uninstalling the software, see Uninstalling the Printer Software in the User's Guide. Quick Start | E-39 Front Panel Summary Overview ! For more information, see Control Panel under Printer Control in the User's Guide. LED Display 1 READY light: on = ready to receive data; blinking = receiving/printing data; off = offline, warming up 2 ATTENTION light: On = toner low, or drum or fuser needs replacing; blinking = toner cartridge empty; off = normal state. 3 Paper Size Indicators: light indicates which paper size is loaded in Tray 1 E-40 | Quick Start Buttons Press: In the menu mode, advances to the next item. Used with /Recover to generate a drum cleaning page. Press and hold 2-3 sec: Deletes the data in the buffer and executes an internal reset. Press: Enters the Level-1 menu. [. . . ]