User manual FLAM MT 68-57 DIMENSIONS

[. . . ] Written and produced by the FLAMDATA Publications Services Dept. Please address any comments to: Publications Services Department FLAMDATA 532 Fellowship Road Mount Laurel, New Jersey 08054 http://www. okidata. com FLAMDATA is a registered trademark of Oki Electric Industry Company, Ltd. ; Marque déposée de Oki Elecric Industry Company, Ltd. ; Marca Registrada, Oki Electric Industry Company, Ltd. FLAMPAGE is a trademark of FLAM America, Inc. Energy Star is a trademark of the United States Environmental Protection Agency. [. . . ] Pull down the manual feed tray and adjust the paper guides. Insert the envelope--flap down and on the left-- until the printer grips it. Set envelope size and landscape orientation in your software, then issue the print command. FLAMPAGE 6e 11 Connecting Your Printer Make sure your printer is not plugged in and your computer is turned off. The interface cable must be an IEEE 1284 compliant bidirectional parallel cable, and must be shielded and UL and CSA approved. Plug the interface cable into the parallel socket in the printer. Plug the other end into your computer. 2. Plug the power cord into the printer, then into a grounded outlet. 3. The Ready light comes on. POWER ON OFF 12 OL OL 61 Oe Setting Up Section 2: Installing Printer Software FLAMPA Sof are for indow oft Installing the FLAMPAGE 6e Software for Windows 95 1. If "New Hardware Found" prompt appears, click "Driver from disk provided by hardware manufacturer, " then click OK. Insert the FLAMPAGE 6e CD into your CD-ROM drive and go to step 9, then follow the instructions on your screen. Insert the FLAMPAGE 6e CD into your CD-ROM drive. Displays Printer Menu dialog to change user default settings and set display format of the Status Monitor. Displays graphic animation of printing status. Displays printer status and error recovery methods. Status Monitor Detail Display Panel FLAMPAGE 6e 17 Setting Features in the Online Operator Panel The printer menu displays printer defaults which you can modify. To change a default setting, select the appropriate tab. Point to any item on a display to see a pop-up explanation. Select paper feed source-- standard tray, manual, or optional tray. Set print resolution, Select printer emulation, paper darkness setting. orientation, lines per page. Set power save mode, toner save feature. Print demo page, menu setting list, font list, cleaning page. Set memory options. Adjust print position, reset drum counter, select display language. 18 Setting Up Section 3: Printer Maintenance Replacing the Toner Cartridge 1. Open the cover and remove the used toner cartridge. Shake the toner cartridge to evenly distribute toner. 2. Unwrap the new cartridge (Part 52107201). 4. Peel tape off the bottom. For highest print quality, we recommend using genuine Okidata consumable products in your page printer. We cannot control the manufacturing and operating characteristics of non-Okidata toner cartridges or assure the resulting print quality. [. . . ] Small amounts of toner on skin or clothing can easily be removed with soap and cold water. Hot water makes toner harder to remove. Toner inhaled Toner gets in the eyes Note Physical Data Melting Point: 110°C (230°F) Boiling Point: Not applicable Vapor Pressure: Not applicable Vapor Density (Air=1): Not applicable Evaporation Rate (Butyl Acetate=1): Not applicable Specific Gravity (H2O=1): 1. 15 Solubility in water: Negligible Appearance and odor: Black granules, no odor Fire and Explosion Hazard Data Routes of Entry: Inhalation, Ingestion, Eyes, Skin. Flash Point (Method Used): Not applicable Health Hazards: 1. Styrene-Butyl Acrylate Copolymer Subcutaneous implantation of polymeric styrene powder in rats has induced tumors at the site of implantation. Carbon black (Group 3 "Not Classifiable"; IARC) Overexposure to carbon black is associated with causing irritation, conjunctivitis, and corneal hypoplasia of the eyes; minor irritation and eczema of the skin; and throat irritation and bronchitis. [. . . ]