Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual FLUKE 1-4 IN LOW. We hope that this FLUKE 1-4 IN LOW user guide will be useful to you.
Lastmanuals help download the user guide FLUKE 1-4 IN LOW.
Detailed instructions for use are in the User's Guide.
[. . . ] Low- and Mid-Flow Metering Valve Kits for molstic-STM
P/Ns 401885 and 401666 Instruction Sheet
The 1/4 in. molstic-STM is delivered with integrated shut-off/metering valves. These valves provide a measure of flow control for use when calibrating devices that do not have their own flow control means. [. . . ] The long side of the bracket should be perpendicular to the direction of flow through the valve. Using a pair of properly sized wrenches, break the connection between the downstream end of the ® filter element (1) and the female VCR swivel nut (2) on the inlet of the molstic-S. Do not disassemble the parts on the inlet side of the filter element (1). Discard the VCR gasket, which is for one-time use.
Thread the included double female VCR union (non-swivel type), (3), onto the inlet fitting of the metering valve. Leave it approximately one full revolution from the fully stopped position. VCR gasket (P/N 102183) securely against the sealing surface inside the double female VCR union (non-swivel type) (3). Install the filter (1) and upstream plumbing into the female VCR union (3). Hold male body stationary with a backup wrench. Tighten the female nut 1/8 turn past finger-tight.
Place the flat side of the 60 mm nut plate under the molstic-S platform (see figure below). Align it with the holes in the platform and the valve bracket. Thread the socket head cap screws through the valve bracket and tighten securely into the nut plate.
Do not adjust the supply pressure to the 1/4 in. metering valve in excess of the maximum operating pressure of the molbox: 600 kPaa (87 psia) for molbox1-A700K; 250 kPaa (36 psia) for molbox1A350K.
INSTALLATION OF 1/4 IN. METERING VALVE ONTO MOLSTIC-S PLATFORMS WITH REGULATORS
Do not attempt to completely close off flow using the 1/4 in. They are not designed to be used as shut off valves. Damage to the valve seat can occur.
PARTS INCLUDED WITH 1/4 IN. LOW-FLOW AND MID-FLOW METERING VALVE KITS
The following parts are included in the shipment:
P/N 401885 Low-Flow Metering Valve Kit
DESCRIPTION QTY PART NO.
Use double female swivel union (5) in place of the non-swivel union (3) when installing the metering valve kit (4) onto a molstic-S that has the integrated regulator. [. . . ] VCR is a registered trademark of the Swagelok Company. Viton is a registered trademarks of DuPont deNemours Company. Document 560055a 030108
DH Instruments, Inc.
4765 East Beautiful Lane Phoenix AZ 85044-5318 USA
Tel 602. 431. 9100 Fax 602. 431. 9559 dhi@dhinstruments. com www. dhinstruments. com [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE FLUKE 1-4 IN LOW
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual FLUKE 1-4 IN LOW will begin.
