User manual FLUKE EPROM KIT INSTRUCTIONS FOR PG AND FPG TERMINALS
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual FLUKE EPROM KIT. We hope that this FLUKE EPROM KIT user guide will be useful to you.
Lastmanuals help download the user guide FLUKE EPROM KIT.
Manual abstract: user guide FLUKE EPROM KITINSTRUCTIONS FOR PG AND FPG TERMINALS
Detailed instructions for use are in the User's Guide.
[. . . ] REPLACEMENT EPROM KIT For PG AND FPG TERMINALS
P/N 402372 Instruction Sheet
REPLACEMENT EPROM KIT FOR PG/FPG TERMINALS, INCLUDES:
DESCRIPTION QTY PART NO.
EPROM, PG/FPG Remote (ver 1. 01b)
1
402372
This is a replacement EPROM kit for PG or FPG terminals.
REMOVAL OF PG/FPG VER 1. 01a EPROM
Disconnect power cord. Turn the PG/FPG Terminal on it's back so all four (4) rubber feet show: Remove the feet using a small screwdriver to pop them out. [. . . ] The power supply is mounted in four (4) places with a stainless steel screw, a lock washer and a flat washer (see Figure 2). Unscrew all four of the stainless steel screws, lock washers, and flat washers and retain them for use in remounting the power supply. The screws can be removed using a 2. 5 mm Allen wrench. The power supply can now be removed (see Figures 2 and 3). The old EPROM is located at U5 on the PG/FPG Terminal main board.
Figure 1: PG/FPG Terminal bottom with feet removed.
Figure 2: PG/FPG Terminal power supply board.
Figure 3: PG/FPG Terminal main board. Power supply removed.
REASSEMBLE THE PG/FPG TERMINAL
Install new EPROM 402370 Ver 1. 01b. The EPROM is installed at U5 on the PG/FPG Terminal main board lining up the notch on the EPROM with notch silk screened on the terminal main board (see Figure 4). EPROM notch must line up with notch silk screened on PG/FPG Terminal main board. If installed incorrectly, the EPROM will be destroyed on power up (see Figure 4). Position the power supply board in the correct mounting location with the standoffs on the main board. Install all four of the stainless steel screws, lock washers and flat washers. Tighten using a 2. 5 mm Allen wrench.
The flat washer should be positioned between the surface of the power supply board and the lock washer.
Figure 4: Orientation of EPROM on PG/FPG Terminal main board.
Reattach 3 and 6 pin cables to power supply. [. . . ] Turn power off then on again (do not hold any keys down). The initial display will show DH Instruments, Inc.
Figure 5: Testing the PG/FPG Terminal for correct version.
Document 560082
060328
DH Instruments, Inc.
4765 East Beautiful Lane Phoenix AZ 85044-5318 USA
Tel 602. 431. 9100 Fax 602. 431. 9559 dhi@dhinstruments. com www. dhinstruments. com [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE FLUKE EPROM KIT
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual FLUKE EPROM KIT will begin.
