User manual FLYMO RE 320

[. . . ] ® Original Instructions VENTURER 32 VENTURER 32 (VTR32) VISIMO (VM032) ROLLERMO (RM032) EASIMO (EM032) RE 320 (RE32) ROLLERMO RE320 VISIMO EASIMO AT I FORM NT IN RTA I M P O fore use rence be e refe Read r futur in fo & reta ON Carton Contents start/stop lever cable clip x 2 grassbox handle switchbox lock off button washer x 4 wingknob x 4 bolt x 2 upper handle grassbox upper grassbox lower Easimo only grassbox tongue safety flap electric cable with moulded on plug lower handle x 2 motor cover deck instruction manual IMPORTANT !Please check the contents of the carton are correct BEFORE assembling your new Flymo product. The Loose Parts Pack is packaged underneath the deck of the product. IF ANY PARTS ARE MISSING CONTACT:Husqvarna UK Ltd. [. . . ] The normal plug fuse and household fuse only protect the electrical equipment and are not a safeguard against electrocution. If your product is hard wired i. e. non-detachable mains electric cable, a conversion kit and extension cable is available from all Approved Service Centres which can be found in your local Yellow Pages. Assembly Instructions A 3 2 · The Loose Parts Pack is packaged underneath the deck. Place the bolt (A2) through the hole in the lower handle (A1) until the lower handle fits into the recess (A3) 2. Place the washer (B1) and the wing knob (B2) on to the bolt and tighten the wing knob. Assembly of Upper Handles to Lower Handles. Ensure the upper handle is located correctly with the lock-off button on the switchbox uppermost. Ensure the upper handle (C1) and the lower handle (C2) are aligned correctly. Fit the bolts (C3), washers (C4) and wing knobs (C5). Fit the cable to the handles with the clips provided. Make sure the cable is not trapped between the upper and lower handles. Slide the grassbox tongue into the slots in the grassbox lower until it clicks securely into position (D) 2. Push the grassbox handle into the slots in the grassbox upper until it clicks securely into position. Starting at the rear of the grassbox, locate the grassbox upper into the grassbox lower by aligning the clips (F1). Ensure all clips are correctly located. (F2) before clicking into position. Clip the two halves together, ensuring all clips are securely connected. 1 B 1 2 C 3 4 1 5 2 D E F1 F2 Grassbox G 1 Fitting Fully Assembled Grassbox to Lawnmower. Lift safety flap (G1) Make sure the discharge chute is clean and free from debris (G2) Locate fully assembled grassbox onto 2 location points (G3) at the rear of the deck as illustrated in pic. H Locate safety flap onto the top of the grassbox. Ensure the grassbox is securely located. AFTER FITTING ENSURE NO GAP REMAINS BETWEEN THE SAFETY FLAP AND THE GRASSBOX. For larger areas of grass where grass collection is not required you can use your lawnmower without the grassbox. The design of the safety flap permits the cut grass to be discharged downward behind the machine. 3 4. 2 · H · · J Visimo Only Grassbox Full Window (Visimo Only) · As the grassbox fills up, grass will be visible through the window (J). · When the window/grassbox is full it is time to empty the grassbox. grassbox empty grassbox full K Cutting Height Adjustment L 2cm 4cm 6cm Cutting Height Adjustment (K) & (L) · Height of cut is adjusted by raising or lowering the Front and Rear Wheels. [. . . ] * Failures as a result of not reporting an initial fault. * Failures as a result of sudden impact. * Failures as a result of not using the product in accordance with the instructions and recommendations contained in this Operator's Manual. * Machines used for hire are not covered by this guarantee. [. . . ]