User manual FLYMO SPRINTER 330

[. . . ] FO T IN AN nce O RT e use M P efor efere I re r ead b for futu R tain & re AT I O RM N For all customer enquiries or for replacement parts, contact:- 01325 300303 www. flymo. com eop. customer. services@electrolux. co. uk ¤ 1 Carton Contents start/stop lever switchbox lock off button upper handle bolt x 2 cable clip x 2 lower handles (x 2) washer x 2 (M8) nut x 2 (M8) lower handle knob (x 2) motor cover wheels (x 4) instruction manual deck spanner grassbox lower washer x 2 (M6) nut x 2 (if applicable) safety flap grassbox handle grassbox upper upper handle knob x 2 electric cable with moulded on plug IMPORTANT !Please check the contents of the carton are correct BEFORE assembling your new Flymo product. IF ANY PARTS ARE MISSING CONTACT:Electrolux Outdoor Products Customer Service Department direct Telephone : 01325 300303 Fax : 01325 318193 Safety If not used properly this lawnmower can be dangerous!This lawnmower can cause serious injury to the operator and others, the warnings and safety instructions must be followed to ensure reasonable safety and efficiency in using this lawnmower. [. . . ] Place the washer and wing knob onto the end of the tie rod and firmly tighten. Repeat on the other side. B 1 C 2 1 D 8 9 Assembly of Upper Handles to Lower Handles. Insert the nuts into the upper handle wing knobs. Ensure the upper handle is located correctly with the lock-off button on the switchbox uppermost. Ensure the upper handle and the lower handle are aligned correctly. (B) 4. Fit the bolts, washers and wing knobs. (B) 5. Fit the cable to the handles with the clips provided. Make sure the cable is not trapped between the upper and lower handles. 7 1 2 3 4 5 6 Grassbox Assembly 1. Insert the grassbox handle into the grassbox upper, as illustrated in fig C, and press firmly down until the handle clicks into place. Align the grassbox upper with the grassbox lower. Locate the clips in the numerical order illustrated in Fig D, ensuring all the clips are firmly in place. 4 Cutting Height Adjustment E Cutting Height Adjustment (E) & (F) · Height of cut is adjusted by raising or lowering the wheels. There are five heights of cut on this product. HEIGHT OF CUT Low WHEELS POSITION Front position 1 Back position 1 Front position 1 Back position 2 Front position 2 Back position 2 Front position 2 Back position 3 Front position 3 Back position 3 · Low to Medium Medium F Medium to High High · NOTE A medium height of cut is recommended for most lawns. The quality of your lawn will suffer and collection will be poor if you cut too low. 1 2 3 Grassbox G Fitting Fully Assembled Grassbox to Lawnmower. Make sure the discharge chute is clean and free from debris. Locate fully assembled grassbox onto the location point at the rear of the deck (G1) Locate safety flap onto the top of the grassbox. Ensure the grassbox is securely located. AFTER FITTING ENSURE NO GAP REMAINS BETWEEN THE SAFETY FLAP AND THE GRASSBOX. For larger areas of grass where grass collection is not required you can use your lawnmower without the grassbox. The design of the safety flap permits the cut grass to be discharged downward behind the machine. · · 1 5 Starting and Stopping H J To Start your Lawnmower 1. Form loop in mains cable and push the loop through the slot. To secure, position loop over the hook and pull the cable back through the slot (J). [. . . ] DL5 6UP Certify that a sample of the above product has been tested using directive 81/1051/EEC as a guide. The maximum Aweighted sound pressure level recorded at operator position under free field semi anechoic chamber conditions was :I, the undersigned M. Bowden of Electrolux Outdoor Products, Aycliffe Industrial Park, NEWTON AYCLIFFE, Co. DL5 6UP Certify that a sample of the above product has been tested using ISO 5349 as a guide. [. . . ]