User manual FORD F750-2005

[. . . ] Table of Contents Introduction Congratulations Safety and environment protection Symbol glossary 4 4 5 8 Vehicle inspection guide Instrumentation Warning and control lights Gauges 11 21 21 26 Entertainment systems AM/FM AM/FM AM/FM AM/FM stereo stereo cassette stereo cassette with CD stereo with CD 30 30 32 35 39 Climate controls Heater only Manual heating and air conditioning 44 44 45 Lights Headlamps Turn signal control Interior lamps Bulb replacement 47 47 48 49 49 Driver controls Windshield wiper/washer control Steering wheel adjustment Power windows Mirrors Speed control 52 52 53 55 56 58 1 Table of Contents Locks and security Keys Locks 64 64 64 Seating and safety restraints Seating Safety restraints Child restraints 65 65 70 79 Driving Starting Brakes Air suspension Transmission operation Vehicle loading 87 87 93 115 118 134 Roadside emergencies Hazard flasher switch Fuses and relays Jump starting Wrecker towing 139 140 140 147 150 Customer assistance Getting assistance outside the U. S. and Canada Ordering additional owner's literature Reporting safety defects (U. S. only) 154 156 157 157 Cleaning Cleaning your vehicle Repairing paint chips Underbody preservation 158 158 159 161 2 Table of Contents Maintenance and specifications Hood Engine oil Battery Fuel information Lubricant specifications Refill capacities 162 169 170 180 189 213 222 General maintenance information Index 227 263 All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company. [. . . ] When more power is required, shift to a lower gear and accelerate the engine near the governed speed. Driving hints The following driving hints are provided as a brief, general guide in operating the different manual transmissions used in your vehicle. · Always use the lowest gear to start the vehicle. · Do not slam or jerk the gearshift lever into gear. · When shifting into 1 (First) or R (Reverse) with vehicle standing still, quickly release and depress the clutch pedal (if necessary to complete gear engagement). Shifting with a synchronized transmission With the clutch pedal depressed, use 2 (Second) gear synchronizer to stop the clutch disc rotation; this allows smooth engagement of 1 (First) or R (Reverse) To complete the gear engagement, it may be necessary to apply light pressure to the gearshift lever during initial engagement of the clutch. It takes a second or two to match gear speeds; steady pressure on the gearshift lever will help the synchronizer perform its job more quickly. If the gearshift lever is forced into position, this action defeats the purpose of the synchronizer by causing gear clash. 124 Driving Shifting with a non-synchronized transmission Refer to Clutch brake and Double clutch procedures in the Clutch section of this chapter. Operating the Eaton FS-4205A and FS-5205A 5­speed transmissions The 5-speed transmission is equipped with five forward gears R 2 4 and one reverse. The 2nd, 3rd, 4th and 5th gears are synchronized. The shift pattern is embossed on the 1 3 5 gear shift knob. Do not shift the transmission into R (Reverse) while the vehicle is moving as this could damage the transmission. To go forward With the engine idling, depress the clutch pedal and shift into 1 (First). Engage the clutch while pressing the accelerator to start forward. Operate the clutch and upshift as required by driving conditions. To go backward Reverse is obtained by putting the gearshift lever in R (Reverse) and engaging the clutch while pressing lightly on the accelerator. Operating the Eaton FS­5406A, FS­5406N, FS­6406A and FS­6406N 6-speed transmissions These 6-speed transmissions are equipped with six forward gears and one reverse. All the forward gears R 1 3 5 are synchronized. The shift pattern is embossed on the gear shift knob. 2 4 6 Do not shift the transmission into 1 (First) or R (Reverse) while the vehicle is moving as this could damage the transmission. To go forward With the engine idling, depress the clutch pedal and shift into 1 (First). Engage the clutch while pressing the accelerator to start forward. [. . . ] Use only permanent type coolant that meets Ford specifications WSS-M97B51-A1. See the engine manufacturer's operating guide for supplemental corrosion inhibitor specifications. Check every oil change Oil change intervals are as follows: Power Stroke 10, 000 ; Caterpillar 15, 000 ; Cummins 15, 000 (refer to the Caterpillar and Cummins service manuals for further instructions and information) 235 236 GENERAL MAINTENANCE SERVICES Listed below are vehicle checks that should be made periodically either by the owner or a qualified technician. It is recommended that deficiencies be brought to the attention of your dealer or another qualified service outlet as soon as possible in order that advice regarding the need for service or replacement can be obtained. Maintenance Operation Clean body/door drain holes. [. . . ]