User manual FORD WINDSTAR-2002

[. . . ] Table of Contents Introduction Congratulations Safety and environment protection Symbol glossary 4 4 5 8 Instrument Cluster Warning and control lights Gauges 10 10 16 Entertainment Systems AM/FM AM/FM AM/FM AM/FM stereo stereo cassette (CD changer compatible) stereo cassette with CD stereo with CD 19 19 23 32 44 Climate Controls Heater only Manual heating and air conditioning 58 58 60 Lights Headlamps Turn signal control Bulb replacement 67 67 71 73 Driver Controls Windshield wiper/washer control Steering wheel adjustment Power windows Mirrors Speed control Message center 78 78 80 85 87 88 99 Locks and Security Keys Locks Anti-theft system 112 112 112 113 1 Table of Contents Seating and Safety Restraints Seating Safety restraints Air bags Child restraints 127 127 139 153 160 Driving Starting Brakes Traction control/AdvanceTrac Transmission operation Vehicle loading Trailer towing Recreational towing 173 173 177 180 184 190 192 195 Roadside Emergencies Getting roadside assistance Hazard flasher switch Fuel pump shut-off switch Fuses and relays Jump starting Wrecker towing 197 197 198 198 200 214 219 Customer Assistance The dispute settlement board Utilizing the mediation/arbitration Getting assistance outside the U. S. and Canada Ordering additional owner's literature Reporting safety defects (U. S. only) 220 223 226 226 227 228 Cleaning Cleaning your vehicle Underbody preservation 229 229 234 2 Table of Contents Maintenance and Specifications Hood Engine compartment Engine oil Battery Fuel information Low tire warning system Part numbers Refill capacities Lubricant specifications Engine data Vehicle dimensions 236 237 238 239 243 250 265 269 269 271 273 273 Accessories Index 276 279 All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company. [. . . ] · After step 5 the safety belt warning light will be turned on for three seconds. Within seven seconds of the safety belt warning light turning off, buckle then unbuckle the safety belt. · This will disable BeltMinder if it is currently enabled, or enable BeltMinder if it is currently disabled. Confirmation of disabling BeltMinder is provided by flashing the safety belt warning light four times per second for three seconds. Confirmation of enabling BeltMinder is provided by flashing the safety belt warning light four times per second for three seconds, followed by three seconds with the safety belt warning light off, then followed by flashing the safety belt warning light four times per second for three seconds again. After receiving confirmation, the deactivation/activation procedure is complete. Safety belt extension assembly If the safety belt is too short when fully extended, there is a 20 cm (8 inch) safety belt extension assembly that can be added (part number 611C22). This assembly can be obtained from your dealer at no cost. Use only extensions manufactured by the same supplier as the safety belt. Manufacturer identification is located at the end of the webbing on the label. Also, use the safety belt extension only if the safety belt is too short for you when fully extended. Do not use extensions to change the fit of the shoulder belt across the torso. Safety belt maintenance Inspect the safety belt systems periodically to make sure they work properly and are not damaged. Inspect the safety belts to make sure there are no nicks, tears or cuts, replacing if necessary. All safety belt assemblies, including retractors, buckles, front seat belt buckle assemblies, buckle support assemblies (slide bar-if equipped), shoulder belt height adjusters (if equipped), child safety seat tether bracket assemblies (if equipped), LATCH child seat tether anchors and lower anchors (if equipped), and attaching hardware, should be inspected after 151 Seating and Safety Restraints a collision. Ford recommends that all safety belt assemblies used in vehicles involved in a collision be replaced. However, if the collision was minor and a qualified technician finds that the belts do not show damage and continue to operate properly, they do not need to be replaced, except as described in the Replacing the front passenger and second row bench seat belt assemblies after a collision section of this chapter. Safety belt assemblies not in use during a collision should also be inspected and replaced if either damage or improper operation is noted. Failure to inspect and if necessary replace the safety belt assembly under the above conditions could result in severe personal injuries in the event of a collision. Refer to Cleaning and maintaining the safety belts in the Cleaning chapter. Replacing the front passenger and second row bench seat belt assemblies after a collision All front passenger and second row bench seat belt assemblies adjacent to a sliding door have special energy management retractors designed to further reduce the risk of injury in the event of a head-on collision. These retractors should be replaced if they were used in any accident in which the front airbags deploy. [. . . ] 2 Add the coolant type originally equipped in your vehicle. 270 Maintenance and Specifications LUBRICANT SPECIFICATIONS Item Brake fluid Ford part name Motorcraft High Performance DOT 3 Motor Vehicle Brake Fluid1 Silicone Lubricant Ford part number PM-1 Ford specification ESA-M6C25-A and DOT 3 Door weatherstrips F7AZ-19G208-BA ESR-M13P4-A and F5AZ-19553-AA ESE-M97B44-A Engine coolant Motorcraft VC-4­A (in Premium Engine Canada, Coolant (green Motorcraft colored) CXC-10) Motorcraft VC-7­A WSS-M97B51-A1 Premium Gold Engine Coolant (yellow colored) WSS-M2C153-H Engine oil Motorcraft SAE XO-5W20-QSP 5W20 Super with API Premium Motor Certification Mark Oil Door latch, hood Multi-Purpose XG-4or ESR-M1C159-A latch, auxiliary Grease F5AZ-19G209-AA hood latch, door and liftgate hinges, striker plates, seat tracks, sliding door both sides (upper and lower track) and fuel filler door hinge. 271 Maintenance and Specifications Item Lock cylinders Power steering fluid Automatic transaxle (4F50N) Disc brake caliper rails Ford part name Penetrating and Lock Lubricant Motorcraft MERCON ATF Motorcraft MERCON V ATF2 Motorcraft Silicone Brake Caliper Grease and Dielectric Compound Motorcraft CV Joint Grease (High Temp. ) Ultra-clear Windshield Washer Concentrate Ford part number Motorcraft XL-1 XT-2-QDX XT-5-QM Ford specification none MERCON MERCON V XG-3 ESE-M1C171-A Constant velocity joints Windshield washer fluid XG-2 ESP-M1C207-A C9AZ-19550-AC ESR-M17P5-A 1 Use only brake fluids certified to meet Ford specifications. However, if DOT 3 is not available, DOT 4 fluid can be used. 2 Ensure the correct automatic transmission fluid is used MERCON and MERCON V are not interchangeable. Refer to the scheduled maintenance guide to determine the correct service interval. 272 Maintenance and Specifications ENGINE DATA Engine Cubic inches Required fuel Firing order Spark plug gap Ignition system Compression ratio VEHICLE DIMENSIONS Vehicle dimensions (1) Overall length (2) Overall width (3) Overall height (4) Wheelbase (5) Track - Front (5) Track - Rear Wagon 5 102. 9 1 945. 6 1 727. 2 3 065. 8 1 643. 4 1 600. 2 mm (in) (200. 9) (76. 6) (68. 0) (120. 7) (64. 7) (63. 0) Van mm (in) 5 102. 9 (200. 9) 1 945. 6 (76. 6) 1 678. 9 (66. 1) 3 065. 8 (120. 7) 1 643. 4 (64. 7) 1 600. 2 (63. 0) 3. 8L OHV V6 engine 232 87 octane 1-4-2-5-3-6 1. 3-1. 4 mm (0. 052-0. 056 inch) EDIS 9. 36:1 273 Maintenance and Specifications 4 1 IDENTIFYING YOUR VEHICLE Certification label The National Highway Traffic Safety Administration Regulations require that a Certification label be affixed to a vehicle and prescribe where the Certification label may be located. [. . . ]