Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual FOSSIL OS10. We hope that this FOSSIL OS10 user guide will be useful to you.
Lastmanuals help download the user guide FOSSIL OS10.
Detailed instructions for use are in the User's Guide.
[. . . ] Using a suitable nut driver, remove the pot nuts. Then invert the console and place it on its front.
· `
REMOVE THE CONSOLE BASE :
Refer to fig. 7.
REMOVE THE BLANKING PLATE :
The blanking plate is located below the input connectors on the rear panel of channels 9 to 16. [. . . ] Unscrew the retaining screws and remove the blanking plate.
'
DISCONNECTING THE HARNESS ASSEMBLIES:
Disconnect the MAIN HARNESS (A) plugged into the connectors mounted along the edge of the circuit boards. It is not necessary to disconnect channels 1 to 15. Then disconnect the 16 way MASTER HARNESS (B) from the GROUP circuit board assemblies but not from the MASTER CONNECTOR circuit board assembly (C). Drape the harness over the rear of the console. Disconnect the flexible flat cables (D) plugged into the GROUP and LEFT circuit boards.
C Chan. 24
D Chan. 1
B
A
CONSOLE FRONT
24 channel console inverted with the base cover removed.
fig. 2
FOSSIL OS10 & GL3300 SYS-LINK OPTION 3
"
Place the SYS-LINK circuit board assembly across channels 13 to 16 with the harness to the rear of the console. Take care not to stretch the fader wires that are still connected.
not fitted on OS10 D Chan. 24 B Chan. 1
E SYS-LINK CIRCUIT BOARD
E
A
E
CONSOLE FRONT
24 channel console inverted with the base cover removed.
fig. 3
" ·
Refering to fig. 6, fix the green earth wire to the rear extrusion with the screw provided.
13
REFIT THE HARNESSES :
Refering to fig. 2, re-fit the 16 way MASTER HARNESS (B) onto the GROUP circuit boards and also the MAIN HARNESS (A) onto all circuit boards. Check the harnesses are correctly aligned onto the circuit board connectors with pin 1 aligned with the red stripe of the ribbon harness.
14
REFIT THE BASE :
fig. Turn the console the correct way up and fit the pot nuts and knobs to GROUP 1.
15
PLUG ON THE INTERCONNECTING CABLES:
SYS-LINK connectors are 25way D-type female. Use 25way D-type male to male connector cables. Connect pin one to pin one on all connectors. Standard cables are available from electronic suppliers or computer shops. It is advised that the cable is a screened type less than 10 metres. [. . . ] It is advised that the cable is a screened type less than 10 metres. Use professional quality locking connectors. When connecting to equipment other than the GL Series link all unused audio inputs to 0V earth at the SYS-LINK input.
16
TEST THE SYSTEM:
Test all SYS-LINK inputs and outputs for correct signal level and quality by probing the D-connector pins or by interconnecting two consoles with SYS-LINK fitted. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE FOSSIL OS10
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual FOSSIL OS10 will begin.
