User manual FOSTEX CD-1A INSTALLATION

[. . . ] See the VF160 operation manual for details about how to save/load song data or how to make an audio CD. <Check the contents in the package> This product includes the following in the package. [. . . ] · Before installing the drive, make sure that the power of the VF-160 is off and the power cord is disconnected. · Install the drive correctly according to this manual. Note that damage to the drive caused by inappropriate installation is not covered by the guarantee. 1 Place the VF160 upside down on a material such as a soft cloth, and unscrew the screw that fixes the blank panel. Be careful not to drop the VF160 or give a strong shock to the VF160, which may damage the hard-disk drive built into it. Keep the blank panel for future use in case you unmount the CD-1A. 2 Turn the VF160 over and insert the CD-1A into the slot on the front panel. Push the CD-1A firmly, without forcing, so that the connector of the CD-1A fits into its companion in the slot. connector Unfasten the screw that fixes the blank panel. CD-1A Blank panel Remove the blank panel. Keep the screw mentioned above, which will be used in step 4 below after installing the CD-RW drive. 3 3 Use two screws supplied with the CD-1A to fix the CD-1A to the VF160 from the front panel. Tighten the screws with a screwdriver. Opening/closing the tray · To open the tray, press the eject switch lightly. Pressing the switch will open the tray slightly. Then pull out the tray gently by hand to fully open it. screw position screw position Eject switch 4 Use the screw you removed in step 1 to fix the blank panel supplied with the CD-1A to the front panel. Slant the panel slightly when inserting the panel inside the unit. The tray slightly opens. lens Use the screw you removed in step 1 to fix the blank panel. Pull out the tray to fully open it. <Caution!> Do not touch the lens when pulling out the tray, doing so may damage it and may cause a malfunction. · To close the tray, push the tray inside by hand until locked. Connect the power cord of the VF160 and turn on the power. Make sure that the VF160 starts up, and the LED indicator on the front panel of the CD1A blinks for a few seconds then turns off. Wait until the VF160 display changes to the Normal display from the start-up display, and then you are ready to operate the CD1A. 5 Push until it is locked. 4 Placing/removing a disc The following are some notes on placing and/ or removing a disc. <IMPORTANT!> When placing a disc on the tray, support the tray from the bottom by your hand. If you push the disc to fit into the pivot on the tray without supporting the tray, the tray/drive may be damaged or broken. Also note that the disc must be pushed until it clicks so that it is locked into the pivot securely. Closing the tray without locking the disc may damage the disc. <Note for removing a disc from the tray> When removing a disc from the tray, also support the tray from the bottom by your hand. Also be careful not to unlock the disc from the pivot forcibly, which may damage the tray. · Place the disc with the label side up. When placing the disc, support the tray from the bottom by your hand as shown in the illustration below, and push the disc gently until it clicks so that the disc is locked into the pivot. [. . . ] ADD: C/Garcilaso No. 9, Madrid 28010, Spain TEL: (+34) 91-4470700, 91-4470898, FAX: (+34) 915930716 <GERMANY> NAME: Studio sound & Music GmbH ADD: Industriestrasse 20, D-35041 Marburg, F. Germany TEL: (+49) 6421-92510, FAX: (+49) 6421-925119 <SWEDEN> NAME: Professional Television AB ADD: Kavallerivagen 24, 172 48 Sundbyberg, Sweden TEL: (+46) 8-59798000, FAX: (+46) 8-59798001 <GREECE> NAME: Bon Studio S. [. . . ]