User manual FOSTEX D-824 APPENDIX

[. . . ] APPENDIX <Operation manual for the recorder with the Model 8345 TC/SYNC card installed> This appendix is the operation manual for the recorder with the Model 8345 TC/SYNC card installed. If you use the recorder with the Model 8345 installed, read this appendix, instead of the operation manual included in the Model 8345 package. <Installation of the optional card> The TC/SYNC card should be installed into the recorder at a FOSTEX service station. Do not try to install the card by yourself. Ask your local FOSTEX dealer for the installation after purchasing the Model 8345. <Notes when requesting the installation> There is the possibility of damaging the hard disk when transporting the recorder. [. . . ] After selecting the reference clock, press the EXECUTE/YES key. The selected reference clock is confirmed (set) and the display changes to the similar one to the upper example in step 3 above where [?] flashes. Word Free adat Ana. Word Free Video Vari adat Ana. Video Vari 6. Press the EXIT/NO key (or the STOP button) to exit the SETUP mode. Video Free Video Free adat 5. After selecting the preset, press the EXECUTE/YES key. The selected preset is confirmed (set) and the display changes to the similar one to the upper example in step 3 above where [?] flashes. 6. Press the EXIT/NO key (or the STOP button) to exit the SETUP mode. 5 APPENDIX (Operation manual for the recorder with the Model 8345 TC/SYNC card installed) "Virtual LTC?" menu setting Execute step 1 and 2 in ""Ref. TC ?" menu setting" described earlier. Select the [Virtual LTC?] menu by using the JOG dial and press the EXECUTE/YES key. The current setting is flashing (the default setting when the Model 8345 is installed is [Ena. ] (enable)). SETUP "Offset Disp?" menu setting Execute step 1 and 2 in ""Ref. TC ?" menu setting" described earlier. Select the [Offset Disp?] menu by using the JOG dial and press the EXECUTE/YES key. The current setting is flashing (the default setting when the Model 8345 is installed is [Off]). SETUP OL 0 3 6 9 12 18 24 30 42 44. 1kHz OL 0 3 6 9 12 18 24 30 42 44. 1kHz _ _ 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 SETUP SETUP OL 0 3 6 9 12 18 24 30 42 44. 1kHz _ OL 0 3 6 9 12 18 24 30 42 44. 1kHz _ 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 4. Select [Ena. ] or [Dis. ] by using the JOG dial. Selection Function Enables recording/playback of the virtual LTC. 4. Select [Off] or [ON] by using the JOG dial. Selection Function The real-offset value is not displayed. Ena. (Disable) Disables recording/playback of the virtual LTC. This setting is used when you want to chase the recorder using only the MTC offset setting, ignoring the recorded LTC. With this setting, the TIME CODE OUT terminal outputs MTC or LTC with the MTC offset. On The real-offset value is displayed instead of the REMAIN time when the timebase is set to MTC If you press the STORE key, the display shows [Catch Offset!] for a second, then changes to the edit mode display of the chase offset which will be explained in "GENERATOR Setup" later. After editing the chase offset, pressing the EXECUTE/YES key updates the real-offset value. 5. Use the JOG dial to display the desired recording mode. You can choose from 4 recording modes available. Recording mode Function Timecode that is continuous with the timecode previously recorded will be recorded. This mode is also useful to re-record a discontinuous timecode. Timecode generated by the internal generator will be recorded. Timecode generated by the internal generator will be recorded from the current time of the recorder's internal clock. OL 0 3 6 9 12 18 24 30 42 44. 1kHz _ SURE? Menu for force jamming to external timecode Rec Run 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Free Run Ext Run OL 0 3 6 9 12 18 24 30 42 44. 1kHz Display of internally generated timecode 24H Run _ 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 <CAUTION> OL 0 3 6 9 12 18 24 30 42 44. 1kHz Menu for selecting the output timecode _ 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 The 8345 does not record all timecode information. It records only the ABS time at the recording start point and the timecode offset value. Therefore, if you record discontinuous timecode in the middle, it cannot recognize it. Also note that because the user's bit at the recording start point is maintained, the 8345 cannot recognize user's bit change in the middle. OFFSET CHASE OL 0 3 6 9 12 18 24 30 42 44. 1kHz _ 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Menu for editing the chase offset between external timecode and MTC 3. Press the EXECUTE/YES key after selecting the recording mode. <CAUTION> When you create a new program using the program select function, the LTC with the same MTC offset (which you can see in the [MTC offset?] menu of the Setup mode) as the current program is recorded in the new program. [. . . ] While [MTC] is selected, press the DISP SEL key to select the timecode display. When the recorder is receiving LTC, the display shows the incoming LTC while [TC IN] lights in the display. Synchronization with the VTR 1. Start playback of the VTR. If an offset value is set, the recorder will start playback, chasing the timecode from the VTR with maintaining the offset. 4. Set the slave mode to ON by pressing the EXECUTE/YES key while holding down the SHIFT key. Set the desired offset value by the [MTC OFF SET?] menu of the Setup mode. By setting the desired offset value, the recorder will run with the offset between the VTR and recorder. <CAUTION> · The recorder can chase incoming timecode within the range of continuously recorded timecode. [. . . ]