User manual FOSTEX VF-16

[. . . ] 8288 451 100 Owner's Manual Digital Multitracker INPUT MON OUT PHONES 1/9/A 2/10/B 3/11/C 4/12/D 5/13/E 6/14/F BAL 7/15/G UNBAL INSERT BAL 8/16/H UNBAL INSERT L R TRIM MON OUT PHONES LINE MIC LINE MIC LINE MIC LINE MIC LINE MIC LINE MIC LINE MIC LINE MIC 0 10 0 10 DIGITAL MULTITRACKER PEAK PEAK PEAK PEAK PEAK PEAK PEAK PEAK 1/9/A CH STATUS 2/10/B ORANGE 3/11/C INPUT 4/12/D RED REC 5/13/E 6/14/F PLAY 7/15/G OFF 8/16/H MUTE SCENE RECALL STORE GREEN CH STATUS/CH SEL OPTICAL DR C R L IETC MAP CLEAR EFF EDIT EFF1 EFF2 ACCESS +6 +6 +6 +6 +6 +6 +6 +6 MUTE MUTE PHANTOM 0 0 0 0 0 0 0 0 EFF1/EFF2 CH PARAM EDIT EQ/COMP HI-G/F/Q PRE/POST -10 -10 -10 -10 -10 -10 -10 -10 AUX1/AUX2 COMP INPUT SEL MID-G/F/Q REC ASSIGN BUSS DIRECT SOURCE REC TRK REC TRK DISP SEL PGM SEL SETUP -20 -30 -40 -20 -30 -40 -20 -30 -40 -20 -30 -40 -20 -30 -40 -20 -30 -40 -20 -30 -40 -20 -30 -40 PAN LO-G 1 FADER CH VIEW HOLD/ STORE EDIT 2 3 MARK UNDO/ REDO VARI PITCH LOCATE 4 5 6 7 SCENE SEQ. SCRUB PRE/POST START AUTO RTN AUTO PUNCH IN OUT TIME BASE END IN CLIPBOARD ALIGN SEL OUT A RTN A PLAY - - - - - - - - 1 2 3 4 5 6 7 8 TRACK CH STATUS/CH SEL P . EDIT EVT MEM RECORD STOP PLAY REWIND F FWD AUTO PUNCH +6 +6 +6 +6 +6 +6 +6 +6 +6 CLIPBOARD PLAY L O C AT E A B S 0 LOCATE REC END PREV NEXT 0 0 0 0 0 0 0 0 0 JOG SHUTTLE FADER ADJUST -10 -10 -10 -10 -10 -10 -10 -10 -10 LEVEL ADJUST EXIT/NO EJECT -20 -30 -40 -20 -30 -40 -20 -30 -40 -20 -30 -40 -20 -30 -40 -20 -30 -40 -20 -30 -40 -20 -30 -40 -20 -30 -40 ENTER/YES - - - - - - - - - SHIFT 9 A 10 B 11 C 12 D 13 E 14 F 15 G 16 H TRACK INPUT MASTER CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. ATTENTION: CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRE-SPONDANTE DE LA PRISE ET POUSSER JUSQU' AU FOND. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. "WARNING" "TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. " SAFETY INSTRUCTIONS 1. [. . . ] In the following example, all recalled fader positions are at the lowest positions. The fader icons below are examples of indicating different status. ·The current physical fader position is higher than the recalled position. ·The current physical fader position matches the recalled position. ·The current physical fader position is lower than the recalled position. 3. Repeat the previous step for each channel. Press the [ENTER/YES] key. The display shows "Completed!", immediately followed by the Normal display after each actual (internal) fader position is set to match the corresponding physical fader position. The flashing indicators of the FADER ADJUST turns off. With the example above, all actual faders are set to minimum. 4. After adjusting all the fader positions, press the [EXIT/ NO] key. The indicator of the [FADER ADJUST] key turns off. <Note> The previous description for "Fader adjust" is assumed that "Fader recall setting" of the SETUP mode is set to "CH&MST". However, the default of "Fader recall setting" is "Off". In this setting, the indicator of the [FADER ADJUST] key will not flash when recalling a scene memory, because the fader positions are not recalled and the current fader positions remain effective. Therefore, if you want to make the recalled fader positions of a scene memory effective, set the "Fader recall setting" properly according to your requirement. See "SETUP mode" on page 111 for details about the fader recall setting. Fader adjust When recalling a scene memory, if the recalled fader level does not match the current physical fader position (the red indicator of the [FADER ADJUST] key flashes), you can move the physical faders to match the current fader positions of the scene. The following description is assumed that "Fader recall setting" of the SETUP mode is set to "CH&MST". Press the [FADER ADJUST] key alone. The unit enters the Fader adjust mode. The fader icons appear on the display, as well as flashing "Select CH!". The recalled fader positions are shown as fader knob positions while the current fader positions are indicated by > and <. <Hint> If the fader recall setting of the SETUP mode is set to "CH", the display shows the screen as below when the unit enters the fader adjust mode, indicating all the channel fader positions are recalled, while the master fader position is not recalled. Moving the master fader in this mode directly affects the actual fader level. 2. Select the channel to be adjusted by pressing the corresponding [CH STATUS/CH SEL] key, and move the corresponding physical fader. In the screen example below, the physical fader position of channel 1 matches the recalled fader position. 54 Direct recall of a scene memory Besides recalling a scene memory by selecting the desired scene from the list as described above, you can recall a scene directly. Clearing a scene memory You can clear an unnecessary scene memory by using the following procedure. <Note> You cannot clear the memories in scene number 00. If you select scene number 00 and try to clear the memory, "Warning Can't Clear Current Scene" appears on the display and the operation is ignored. <Note> You can directly recall only the scene memories following to the current scene. For example, if the current scene number is 05, while scene memories are stored in scene numbers 01 through 10, you can directly recall scene numbers 06 through 10. Also note that scene number 00 cannot be recalled. 1. Press the [SCENE RECALL] and [SCENE STORE] keys simultaneously. The display shows the screen for selecting a scene to be cleared. [. . . ] Use the ALIGN SEL function If the "ALIGN SEL" function is used at executing copy paste (or move paste), the sound section located in front of the bar head can be included at pasting. Refer to page 65 for details. 115 MIDI Implementation Chart (Digital Multitracker) Model VF-16 Function. . . . . . . . . . . . . . . . . . . . Basic Channel Default Changed Default Message Altered Note Number: Velocity X X X X ******************************** X True Voice Note ON Note OFF Key's Channel's ******************************** X X X X X X MIDI Implementation Chart Transmitted X X X X X X X X X X X X X Date: Version: V1. 00 Recognized Remarks Mode After Touch Pitch Bend Control Change Program Change System Exclusive X True # ******************************** (rem. 2) : Quarter Frame Common : Song Position : Song Select : Tune System Real Time : Clock : Commands (rem. [. . . ]