User manual FOSTEX VR800

[. . . ] Owner's Manual Model 8288 429 000 Digital Multitrack Recorder OPTICAL ACCESS OL 0 6 12 24 1 2 3 4 5 6 7 8 A SYNC RECORD TRACK 1 2 3 4 5 6 7 8 AUTO RTN AUTO PUNCH START IN OUT END IN CLIPBOARD OUT EXIT / NO EXECUTE / YES PREVIEW EJECT DISP SEL SETUP HOLD/ STORE EDIT UNDO / REDO PGM SEL AUTO RTN AUTO PLAY JOG SHUTTLE VARI PITCH LOCATE TIME BASE SEL SCRUB SHIFT P. EDIT LOC MEM RECORD STOP PLAY REW F FWD AUTO PUNCH CLIPBOARD PLAY LOCATE ABS 0 LOCATE REC END VR800 Owner's Manual (Safety Instructions) CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. ATTENTION: CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. POUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU' AU FOND. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. "WARNING" "TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. " SAFETY INSTRUCTIONS 1. Read Instructions - All the safety and operating instructions should be read before the appliance is operated. [. . . ] While holding down the SHIFT key, press the AUTO END START key, the AUTO PUNCH IN key, or the CLIPBOARD OUT key. The VR800 repeats playback of the "fall sound" at the locate point (edit point). AUTO RTN AUTO PUNCH START IN OUT END IN CLIPBOARD OUT AUTO RTN AUTO PUNCH START IN OUT END IN CLIPBOARD OUT PREVIEW PREVIEW DISP SEL SETUP HOLD/ STORE EDIT UNDO / REDO HOLD/ STORE EDIT UNDO / REDO DISP SEL SETUP PGM SEL AUTO RTN AUTO PLAY PGM SEL VARI PITCH LOCATE TIME BASE SEL SCRUB VARI PITCH AUTO RTN AUTO PLAY LOCATE TIME BASE SEL SCRUB SHIFT P. EDIT LOC MEM SHIFT P. EDIT LOC MEM <Display indication during the Preview operation> DIGITAL <Display indication during the Preview operation> DIGITAL 44. 1kHz 44. 1kHz ABS LOC H M S F SF LOC ABS H M S F SF SYNC OUT DRIVE SYNC OUT DRIVE CLK AUTO SCSI A. PUNCH CLK AUTO SCSI A. PUNCH Approx. (mute playback) The sound rises at the memory point. The sound falls at the memory point. As shown in the diagram, one-second of data prior to the locate point is muted during playback. The mute is off (fade in) at the locate point and the sound is played back for one second. The VR800 will repeat this operation until you quit the Preview function. As shown in the diagram, one-second of data prior to the locate point is played back, then muted (fade out) at the locate point. The muted playback continues for one second. The VR800 will repeat this operation until you quit the Preview function. 59 VR800 Owner's Manual (Preview Function) 2. To adjust the monitor sound of the selected track so that it can be monitored on the mixer. 3. Press the STOP button or the EXIT/NO key. Note: If data stored in each memory key is in the initial state, all memory keys will be in ABS time 00H 00M 00S. In other words, the program head value is in the memory. Should fade out preview be executed in this condition, the [Void Data !] message and memory data [00H 00M 00S] will alternately flash in the display as a warning. However, for fade in preview, this will function as the memory data [00H 00M 00S] point. Trimming the sound while previewing You can trim the position of the locate point (edit point) using the JOG dial while you preview the sound. At this time, you can also adjust the size of the trimming steps (the amount of offset controlled by the JOG dial). Trimming allows you to fine-tune the position of the locate point stored in the memory keys while previewing the sound. Use this function to change the Auto Punch In/Out points, the start point of Copy & Paste and Move & Paste, and the start and end points of the Erase function. <Notes> · You can audition the result of trimming during the next preview. That is, if you trim the position while previewing the sound for the first time, you can check the result when you preview the sound next time. · If the locate point is shifted outside the range of the preview playback as a result of trimming, [Void Data!] and the locate point indication appear alternately. In this case, you cannot use the Preview function. Trim the position again so that it will be within the playback range. · When Auto Punch mode is turned on and you trim the Auto Punch In or Auto Punch Out point while previewing the sound with [Void Data!] indicated on the display, Auto Punch mode will be cancelled. 1. Start previewing the sound by following the steps described on the previous page. Use the JOG dial to trim the position. When previewing starts, the unit of JOG trimming flashes on the screen. For example, value of SF (sub-frame) flashes if ABS Time Base or MTC Time Base is selected. [. . . ] 2. 0kg : 120VAC 60Hz : 230V~ 50/60Hz : approx. 15W <WORD OUT> Connector Output level Load impedance : BNC (X 1) : TTL level : 75 Weight Power supply <PUNCH IN/OUT> Connector : ø6mm Phone jack (X 1) (An optional FOOT SW Model 8051 can be connected. ) Power consumption * Specifications and appearance are subject to change without notice for product improvement. * FDMS-3: Fostex Disk Management System-3. * FDIO-1 Ver. 2: Fostex Data In Out-1 Ver. 2 symbol are trademarks of Alesis Recording/Reproducing <Recording medium> :3. 5 inch, hard disk (E-IDE type) :External SCSI device (SCSI-2, unbalanced transmission format) <Recording format> : FDMS-3* <Recording mode> :ADAC 8ch mode: 8 real tracks+16 additional tracks (44. 1kHz/A. D. A. C. ) :Master 8ch mode: 8 real tracks+16 additional tracks (44. 1kHz/16bit linear) OPTICAL 118 VR800 Owner's Manual (Maintenance/Specifications) Declaration of EC Directive This equipment is compatible with the EMC Directive (89/336/EEC) - Directive on approximation of member nation's ordinance concerning the electromagnetic compatibility and with the Low Voltage Directive (73/23/EEC) - Directive on approximation of member nation's ordinance concerning electric equipment designed to be used within the specified voltage range. The Affect of Immunity on This Equipment The affect of the European Specification EN50082-1 (coexistence of electromagnetic waves - common immunity specification) on this equipment are as shown below. * In the electrical fast transient/burst requirements, radiate electromagnetic field requirements and static electricity discharging environment, this could be affected by generation of noise in some cases. FOSTEX DISTRIBUTORS LIST IN EUROPE * Including non-EU countries. [. . . ]