User manual FUJIFILM @XIA IX-10

[. . . ] User's Manual About this manual This manual is designed to assist you in using the ix-10 Digital Camera. Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the contents. The information in this document is subject to change without notice. Edition 2 nd Edition, June, 2001 Copyright © Copyright 2001 This document contains proprietary information protected by copyright. [. . . ] You can also save the video to your PC as a Windows AVI file. Unpacking the ix-10 Digital Camera Upon receiving your ix-10 Digital Camera, open the package and carefully remove the contents. If anything is missing or damaged, please contact your dealer immediately. The shipping carton should contain the following items: · · · · · · · · · ix-10 Digital Camera 2 MB SmartMediaTM Card Camera Strap Soft Case USB connector cable Video Cable Two AA alkaline batteries Software on CD-ROM Camera Manual Do not throw the carton away. You may need it later if you have to return the ix-10 Digital Camera for repairs. 2 Key features & accessories Features The ix-10 Digital Camera comes with the following advanced features: · · · · · · · 1/3-inch CMOS image sensor LCD status panel 24-bit RGB JPEG image format Image resolution up to 640 x 480 pixels SmartMedia card (2 MB) image storage Auto exposure and flash Bundled software allowing you to perform advanced image manipulation Optional accessories You can purchase bigger SmartMedia cards to increase the capacity of the ix-10 Digital Camera. 2. Set the main switch to OFF. To open the battery compartment cover, slide the cover as shown, then open. 3. Note the battery polarity on the inside cover and insert the batteries. 4. Close the battery compartment cover and slide shut. 9 Battery display When you insert new batteries into your ix-10 Digital, the battery status icon in the LCD display indicates a fully charged battery. Refer to the following table: Battery icon Meaning The batteries have a full charge. Replace the batteries with fresh batteries. 10 Turning the camera on and off Refer to the following to turn the ix-10 Digital Camera on and off: 1. Slide the on/off switch to ON. 2. 3. Check the current settings in the LED status display. (See LED status display on page7. ) To turn the camera off, set the main switch to OFF. Note: If you do not press any button for three minutes, the camera will beep and power off automatically. To turn the camera back on, slide the main switch to OFF, wait for one second, and then switch the camera back on. 12 Taking pictures Follow these instructions to take a picture with your ix-10 Digital Camera: 1. Turn the camera on. When the green LED indicator lights, the camera is ready to take a picture. LED Indicator Power On/off Switch 2. 3. Check the current settings in the LCD status display. Refer to page 7 for information on LCD status display icons. Press the mode button to set the image resolution; HI (fine) and LO (standard). Refer to page 14 for information on the mode button. (See Setting the flash on page 15 for more information. Flash Button Mode Button 4. 5. Press the snapshot button to take the picture. You hear a beep as the picture is taken. The LCD display indicates the number of pictures you have left. Snapshot Button 13 Resolution The following table describes the resolution settings: HI LO 640 x 480 fine resolution, 33 images maximum (using the 2 MB SmartMedia card). 320 x 240 standard resolution, 133 images maximum (using the 2 MB SmartMedia card). Use this setting for smaller file sizes. The Mode button The ix-10 Digital Camera has six operational modes that can be accessed by pressing the mode button: Mode Button Pressing the mode button scrolls through the six operational mode choices: Note: The mode button has a response time of 0. 2 seconds. 14 Setting the flash Follow these instructions to set the flash for the ix-10 Digital Camera: 1. Turn the camera on. When the green LED indicator lights, the camera is ready to take a picture. LED Indicator Power On/off Switch 2. Check the current settings in the LCD status display. [. . . ] The camera may be waiting for the flash to charge. If the camera is full, you cannot take any more pictures. If the resolution is set to high (HI), set the resolution to normal (LO). Otherwise, delete some pictures to free up memory. Refer to page 18. Is the camera connected to a computer? [. . . ]