User manual FUJIFILM FINEPIX_REAL 3D V1

[. . . ] BL00969-200 EN DIGITAL VIEWER Before You Begin First Steps Owner's Manual Thank you for your purchase of this product. This manual describes how to use your FUJIFILM FinePix REAL 3D V1 digital viewer and the supplied software. Be sure that you have read and understood its contents before using the viewer. Viewing Pictures More Menu Options Connections Troubleshooting Appendix For information on related products, visit our website at http://www. fujifilm. com/products/index. html For Your Safety IMPORTANT SAFETY INSTRUCTIONS · Read Instructions: All the safety and operating instructions should be read before the appliance is operated. · Retain Instructions: The safety and operating instructions should be retained for future reference. [. . . ] 28) The meanings of some technical terms may be found here. Symbols and Conventions The following symbols are used in this manual: 3 Caution: This information should be read before use to ensure correct operation. 1Note: Points to note when using the device. 2 Tip: Additional information that may be helpful when using the device. Menus and other text in the display are shown in bold. In the illustrations in this manual, the display may be simplified for explanatory purposes. Package Contents Before using the viewer, confirm that the package contains these items: POWER 3D / 2D SLIDE SHOW MENU /OK DISP /BACK VOLUME PARALLA X FinePix REAL 3D V1 digital viewer Remote control (ships with battery installed) Stand · USB cable · Warranty · Owner's Manual (this manual) AC power adapter Software CD Memory Cards This product supports xD-Picture Card, and SD and SDHC memory cards. In this manual, these are referred to as "memory cards. " For more information, see page 29. 2 Introduction Parts of the Viewer and Remote Control The same numbers are used for controls that appear both on the viewer and the remote. Unless otherwise noted, the controls on the remote perform the same functions as those on the viewer; the descriptions in this manual generally refer to the remote. POWER Before You Begin SLIDE SHOW 3D / 2D MENU /OK DISP /BACK VOLUME PARALLAX No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Viewer (front view) Infrared receiver (for remote control) Infrared data port (for data transfer) Display g (3D/2D) button Q (parallax) button I (slide show) button MENU/OK button DISP/BACK button 6 button 7 button Touch bar (left/right) -- (See back view) -- Remote control -- -- -- g 3D/2D button Q PARALLAX (+/­) buttons I SLIDE SHOW button MENU/OK button DISP/BACK button 6 button 7 button 8 button 9 button VOLUME (e/b) buttons POWER button Battery holder Page 5 23 -- 17 17 12 10 15 10 -- 9 6 3 Introduction No. 1 2 3 4 5 6 7 8 9 Memory card slot cover Stereo speakers T (power) button Tripod mount Hole for stand USB host connector Connector for AC power adapter Mini-B USB connector Memory card slot Viewer (back view) OPEN Page 8 -- 9 7 7 -- 9 25 8 4 Readying the Remote Control A battery is inserted in the remote control at shipment. Before using the remote control, remove the plastic insulating sheet from the battery chamber. 1 Note The battery supplied with the remote control is intended for trial use only. Replace the battery as described on page 6 if the remote control does not function as expected. Using the Remote Point the remote at the infrared receiver on the digital viewer. 3 m (9. 8 ft. ) or less First Steps Insulating sheet Maximum vertical and horizontal angle approx. 30 ° 3 Caution Do not place stickers or other obstructions over the infrared receiver. 5 Readying the Remote Control Replacing the Battery If the remote control does not function as expected, replace the battery with a fresh CR2025 battery (available separately from third-party suppliers). 1 Turn the remote control over and remove the battery holder. Remove battery holder, keeping latch pressed to right Remove the old battery 2 "+" indicator uppermost. from the holder and insert a fresh battery as shown, with the 3 Caution Insert the battery in the correct orientation. 3 Slide the holder into the remote control until the latch clicks into place. 6 Attaching the Stand Attach the stand to the frame. a towel 1 Placedown onor other soft cloth on a level surface such as a table and place the viewer face the cloth. 2 Gently screw the stand into the hole on the back of the viewer as shown. First Steps 3 Stand the viewer as shown. Wide orientation Tall orientation 1 Note The stand can be used in tall orientation when viewing D images, but must be in wide orientation to provide a C effect with C images. Tall orientation pictures can be rotated for display in wide orientation using the ORIENTATION option in the setup menu. 3 Caution The viewer should only be used on a table or other flat horizontal surface; do not hang the viewer from a picture hook or mount it on a wall or other vertical surface using double-faced tape. 2 Tip: The Tripod Mount The viewer can also be placed on a tripod using the tripod mount. 7 Inserting Memory Cards The viewer can be used with the memory cards listed on page 29 (for information on supported file formats, see page 30). Before inserting memory cards into the viewer, be sure to copy any important files to a computer. To insert a memory card: 1 Open the card slot cover. 1 Note The viewer turns off automatically when the cover is opened. shown by 2 Holding the memoryitcard asinto place. the indicator next to the memory card slot, slide the card in until clicks xD-Picture card SD/SDHC card 3 Caution Be sure the card is in the correct orientation; do not insert it at an angle or use force. 1 Note The viewer may be unable to display files that have been modified with a computer. [. . . ] The following information is subject to change without notice. NORTH AMERICA Canada U. S. A. Technical support Repair service Technical support Repair service Technical support & repairs Technical support & repairs Technical support & repairs Technical support & repairs Technical support & repairs Technical support & repairs Technical support & repairs Technical support Repair service Technical support & repairs Technical support & repairs Technical support & repairs Technical support & repairs Technical support & repairs TEL 1-866-818-FUJI (3854) http://www. fujihelp. ca TEL 1-800-263-5018 http://www. fujihelp. ca TEL 800-800-3854 digitalinfo@fujifilm. com TEL 800-659-3854 TEL +54-11-4836-1000 servtec@imageneinformacion. com. ar TEL +591 33 44 1129 gciagral@bibosi. scz. entelnet. bo TEL 0800-12-8600 camarasdigitais@fujifilm. com. br TEL 56-2-6781200 serviciotecnico@reifschneider. cl TEL +57 1 338-0299 animex@etb. net. co CENTRAL AND SOUTH AMERICA Argentina Bolivia Brazil Chile Colombia Ecuador Imagen e informacion S. A. Reifschneider SA Animex de Colombia Ltda. [. . . ]