User manual FUJITSU SIEMENS D1875

[. . . ] answers Mainboard D1875 English 2 Technical Manual Sie haben . . . . . . Wenden Sie sich bitte an: · Ihren zuständigen Vertriebspartner · Ihre Verkaufsstelle Aktuelle Informationen zu unseren Produkten, Tipps, Updates usw. finden Sie im Internet: http://www. fujitsu-siemens. com oder http://www. fujitsu-siemens. com/mainboards Are there . . . . . . any technical problems or other questions you need clarified? [. . . ] Reserved - switch 3 and switch 4 (if present) Switch 3 and 4 are reserved. The position of the switch doesn't matter. 18 - English A26361-D1875-Z120-1-6319, Edition: 1 Add-on modules / Upgrading ! Exit energy-saving mode, switch off the system and remove the power plug from the mains outlet, before carrying out any of the procedures described in this chapter!Even when you have switched off the device, parts (e. g. memory modules, AGP and PCI extension boards) are still supplied with power. Replacing processor Technical data · · · Pentium 4 with 400/533/800 MHz Front Side Bus (FSB) in the mPGA478 design. Celeron with 400 MHz or 533 MHz Front Side Bus in the mPGA478 design A current list of the processors supported by this mainboard is available on the Internet at: www. fujitsu-siemens. com/mainboards. Removing and installing processors Remove the fan that there may be and the heat sink. 3 2 4 5 1 A Pull the lever in the direction of the arrow (1) and lift it as far as it will go (2). Remove the old processor from the socket (3). Insert the new processor in the socket so that the angled corner of the processor matches the coding on the socket (A) with regard to the position (4). i The angled corner of the processor can also be at a different location than shown in the illustration. Push the lever back down until it clicks into place (5). A26361-D1875-Z120-1-6319, Edition: 1 English - 19 Replacing processor Mounting heat sink Be sure to use heat conducting material between the processor and the heat sink. If a heat conducting pad (rubber-like foil) is already applied to the heat sink, then use it. Otherwise you must apply a very thin layer of heat conducting paste. Heat conducting pads can only be used once. If you remove the heat sink, you must clean it and apply new heat conducting paste before you remount it. Please note that, depending on the heat sink used, different heat sink mounts are required on the mainboard. i If a counter-plate is mounted on the underside of the mainboard for reinforcement, no heat sinks of the type "Intel Boxed" may be used. Otherwise the retaining clips of the heat sink will be damaged. When using an "Intel Boxed" heat sink, the mainboard must be converted. This conversion set is either included with the mainboard or is available separately. If no counter-plate is mounted, you can use both "Intel Boxed" heat sinks and standard heat sinks. If you use the "Intel Boxed" heat sink, the mainboard will bend due to the high pressure of the retaining clips. Depending on the configuration variant, you must pull a protective foil off the heat sink or coat the heat sink with heat conducting paste before fitting it. Depending on the processor variant, clips may also be supplied for mounting the heat sink that fix it in place. Ê When you have mounted the optional fan, connect the fan plug to the corresponding connection on the mainboard. 20 - English A26361-D1875-Z120-1-6319, Edition: 1 Upgrading main memory Upgrading main memory Technical data Technology: Size: Granularity: DDR 333 or DDR 400 unbuffered DIMM modules 184-Pin; 2. 5 V; 64 Bit, no ECC 128 Mbyte to 2 Gbyte DDR 400 SDRAM / DDR 333 SDRAM 128, 256, 512 or 1024 Mbyte for one socket · A current list of the memory modules recommended for this mainboard is available on the Internet at: www. fujitsu-siemens. com/mainboards. At least one memory module must be installed. Memory modules with different memory capacities can be combined. ! You may only use unbuffered 2, 5 V memory modules. Buffered memory modules are not supported. DDR-DRAM memory modules must meet the PC2700 or PC3200 specification. Memory clock pulse speed The memory clock pulse speed is affected by the chipset and Front Side Bus. The table shows the memory speed in dependence on the Front Side Bus. Front Side Bus (MHz) DDR400 (MHz) DDR333 (MHz) 800 533 400 Installing a memory module 400 400 400 333 333 333 2 2 Push the holders on each side of the memory slot outwards. [. . . ] If the message is still displayed, please contact your sales outlet or customer service centre. Invalid System Configuration Data In the Advanced menu of the BIOS Setup set the entry Reset Configuration Data to Yes. Invalid System Configuration Data - run configuration utility Press F1 to resume, F2 to Setup This error message may be displayed if the machine was switched off during system start-up. Call BIOS Setup and switch to the Advanced menu. Select the menu item Reset Configuration Data and change the setting to Yes. Save the change and terminate BIOS Setup. [. . . ]