User manual FUJITSU SIEMENS PCD-6H

[. . . ] Questo manuale è stato stampato su carta da riciclaggio. Denna handbok är tryckt på recyclingpapper. Dit handboek werd op recycling-papier gedrukt. Herausgegeben von/Published by Siemens Nixdorf Informationssysteme AG D-33094 Paderborn D-81730 München Bestell-Nr. /Order No. : A26361-D931-Z121-5-7619 Printed in the Federal Republic of Germany AG 1296 12/96 A26361-D931-Z121-1-7619 Is there . . . . . . any technical problem or other question you need clarified?. . . [. . . ] Disabled The ROM area is not copied to fast RAM (default entry). Peripheral Configuration calls the submenu in which you can set the interfaces and controllers. Phoenix BIOS Setup Copyright 1985-94 Phoenix Technologies Ltd. Advanced Peripheral Configuration Serial 1: Serial 2: Serial 2 Mode: Parallel: Parallel Mode: Diskette Controller: Hard Disk Controller: Secondary] Mouse Controller: [Auto] [Auto] [Standard] [Auto] [Printer] [Enabled] [Primary And [Enabled] Item Specific Help F1 Help ESC Exit Select Item Select Menu -/+ Enter Change Values Execute Command F9 Setup Defaults F7 Previous Values Example for submenu Peripheral Configuration 18 A26361-D931-Z121-5-7619 Advanced system settings Settings in BIOS Setup Serial 1 / Serial 2 - Serial port This field selects the address and the interrupt used to access the relevant serial port. 3F8h, IRQ4, 2F8h, IRQ3, 3E8h, IRQ4, 2E8h, IRQ3, Auto Disabled The serial port is set to the shown address and interrupt. The serial port is automatically set to the next available combination (address, interrupt) (Default entry). The corresponding interrupt and address are free. Serial 2 Mode This field defines whether the second serial port is used as the standard port or as the infrared interface. If you wish to use infrared data transfer, an infrared interface with the associated hardware must be incorporated in the device. Standard The port operates as a serial port. (Default) IRDA (Infra-Red Data Association) The serial port permits infrared data transfer up to 115 kbit/s. External serial port 2 does not function. Parallel This field selects the address and the interrupt used to access the parallel port. 378h, IRQ7, 278h, IRQ5, 3BCh, IRQ7 Auto Disabled The parallel port is set to the shown address and interrupt. The parallel port is automatically set to the next available combination (address, interrupt) (Default entry). The parallel port is disabled. A26361-D931-Z121-5-7619 19 Settings in BIOS Setup Advanced system settings Parallel Mode This field is used to specify whether the parallel port is to be used as a bidirectional input/output port or just as an output port. ECP and EPP transfer modes allow faster transfer rates of 2 and 2. 4 Mbytes/s. Disabled No PCI interrupt is used for the PCI board in the assigned PCI slot. IRQ03, IRQ04, IRQ05, IRQ06, IRQ07, IRQ09, IRQ10, IRQ11, IRQ12, IRQ14, IRQ15 The PCI interrupt is switched to the selected ISA interrupt. You may not select an ISA interrupt that is used by a component on the system board (e. g. PCI Device, Slot #n: Default Latency Timer specifies the lowest number of clock cycles in which a PCI master module can be active at the PCI bus. n stands for the number of the PCI slot. Yes The value predefined by the PCI module is accepted. The entry in the corresponding field for PCI Device, Slot #n: Latency Timer is ignored. (Default entry) No The value predefined by the PCI module is ignored. The value set in the corresponding field for PCI Device, Slot #n: Latency Timer determines the number of clock cycles. PCI Device, Slot #n: Latency Timer Condition: the corresponding field for PCI Device, Slot #n: Default Latency Timer must be set to No. The field defines the lowest number of clock cycles in which a burst can be transferred on the PCI bus. n stands for the number of the PCI slot. [. . . ] Kontrollera hårddiskens anslutningar och insticksbryggorna. Incorrect Drive A - run Setup Incorrect Drive B - run Setup Korrigera inställningen för diskettenheten i menyn Main i BIOS-Setup-menyn. Invalid NVRAM media type Starta upp PCn på nytt. Om meddelandet fortfarande visas bör du kontakta din återförsäljare eller vår kundservice. Keyboard controller error Anslut ett annat tangentbord. Om meddelandet fortfarande visas bör du kontakta din återförsäljare eller vår kundservice. Keyboard error Kontrolla att tangentbordet är korrekt anslutet. Keyboard error nn Frigör den angivna tangenten (nn är tangentens hexadecimalkod). Monitor type does not match CMOS - RUN SETUP Korrigera inställningarna för bildskärmtypen i menyn Main i BIOS-Setup menyn. Operating system not found Kontrollera inställningarna för hårddisken och diskettenheten i menyn Main i BIOS-Setup-menyn. A26361-D931-Z121-5-7619 53 Felmeddelanden Parity Check 1 Parity Check 2 Starta upp PCn på nytt. Om meddelandet fortfarande visas bör du kontakta din återförsäljare eller vår kundservice. Previous boot incomplete - Default configuration used Om du trycker på funktionstangenten F2 , kan du kontrollera och korrigera inställningarna i BIOS-Setup. [. . . ]