User manual FUJITSU SIEMENS SCENIC EDITION D6/M6

[. . . ] Microsoft, MS, MS-DOS und Windows sind eingetragene Warenzeichen der Microsoft Corporation. PS/2 und OS/2 Warp sind eingetragene Warenzeichen von International Business Machines, Inc. Alle weiteren genannten Warenzeichen sind Warenzeichen oder eingetragene Warenzeichen der jeweiligen Inhaber und werden als geschützt anerkannt. Copyright ã Fujitsu Siemens Computers GmbH 2002 Alle Rechte vorbehalten, insbesondere (auch auszugsweise) die der Übersetzung, des Nachdrucks, der Wiedergabe durch Kopieren oder ähnliche Verfahren. [. . . ] How to dismantle and reassemble the device is described in the Operating Manual accompanying the device. Please observe the safety information provided in the "Important notes" chapter in the device's operating manual. Incorrect replacement of the lithium battery may lead to a risk of explosion. It is therefore essential to observe the instructions in the "Add-on modules" - "Replacing the lithium battery" section. A26361-D1171-Z120-5-7419 English - 1 Important notes The shipped version of this board complies with the requirements of the EEC directive 89/336/EEC "Electromagnetic compatibility". Compliance was tested in a typical PC configuration. When installing the board, refer to the specific installation information in the Operating Manual or Technical Manual for the receiving device. Connecting cables for peripherals must be adequately shielded to avoid interference. ! i Components can become very hot during operation. Ensure you do not touch components when making extensions to the system board. The warranty is invalidated if the device is damaged during the installation or replacement of system expansions. Information on which system expansions you can use is available from your sales outlet or the customer service centre. Information about boards To prevent damage to the system board or the components and conductors on it, please take great care when you insert or remove boards. Take great care to ensure that extension boards are slotted in straight, without damaging components or conductors on the system board, or any other components, for example EMI spring contacts. The temperature and system monitoring are controlled by an onboard controller developed by Fujitsu Siemens. The following functions are supported: Temperature monitoring: Measurement of the processor temperature, measurement of the system temperature with an onboard temperature sensor, measurement of the device temperature with an optional temperature sensor (AUX). Temperature control: The temperature is controlled by adjusting the fan speed and/or by reducing the clock frequency of the processor. The clock frequency of the processor is dependent upon the setting in the BIOS Setup. It is also possible to boot a device without its own boot hard disk via LAN. Here Bootix LAN BootP and Intel PXE are supported. The LAN RJ45 connector is equipped with a yellow and a green LED (light emitting diode). 1 = Yellow indicator 2 = Green indicator 1 2 Green Yellow a connection exists (e. g. Link Mode: WOL mode: the LAN connection is active. a Magic PacketTM is being received. 8 - English A26361-D1171-Z120-5-7419 Features Screen resolution Depending on the operating system used, the screen resolutions in the following table refer to the system board screen controller. If you are using an external screen controller, you will find details of supported screen resolutions in the Operating Manual or Technical Manual supplied with the controller. [. . . ] At the same time flip the lateral holders upwards until the memory module snaps in place. Removing a memory module 1 1 Ê Ê Flip the holders to the right and left of the location outwards. Pull the memory module out of its location. 14 - English A26361-D1171-Z120-5-7419 Add-on modules Installing network board with WOL Ê Ê Install the network board as described in the operating manual for your unit. Push the WOL cable onto the WOL plug connector of the system board. i To use the WOL functionality of a network board the power supply must provide a 5 V auxiliary voltage of at least 1 A. If the system board was not already incorporated in a device when you bought it you must check whether your power supply can provide the auxiliary voltage. [. . . ]