Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual FUJITSU SIEMENS SCENIC EDITION M6. We hope that this FUJITSU SIEMENS SCENIC EDITION M6 user guide will be useful to you.
Lastmanuals help download the user guide FUJITSU SIEMENS SCENIC EDITION M6.
Manual abstract: user guide FUJITSU SIEMENS SCENIC EDITION M6
Detailed instructions for use are in the User's Guide.
[. . . ] Please contact: · your sales partner · your sales outlet The latest information and updates (e. g. BIOS update) on our mainboards can be found on the Internet under: http://www. fujitsu-siemens. com/mainboards
Vous avez . . .
. . . des questions techniques ou des problèmes ?Veuillez contacter : · Votre partenaire Commercial · Votre point de Vente Les dernières informations ainsi que les updates (p. ex. BIOS-Update) par rapport à nos cartes mères sont à votre disposition sur Internet : http://www. fujitsu-siemens. com/mainboards
Dieses Handbuch wurde auf Recycling-Papier gedruckt. [. . . ] Connect the cable to the hard disk and to the connector on the mainboard. A serial ATA/150 hard disk must be connected with a serial ATA cable. If you have connected one or two hard disks to a serial ATA (one hard disk is possible per serial ATA connection), you must configure the respective settings in the BIOS Setup (further information you can find in the BIOS Setup manual).
Audio front panel
If you want to use the internal connection for the audio front panel for the front side of the system, then proceed as follows: Remove all plug-in jumpers from the audio front panel connection. Connect the cable for the audio front panel.
i
If you connect audio devices on both the front and the back of the system, you can only use the connections Line out and Microphone once each. If you have connected audio devices to both Line out connections, only the connection on the front of the system is active. If you have connected audio devices to both Microphone connections, only the connection on the back of the system is active.
10 - English
A26361-D1567-Z121-1-6319
Pin assignment of internal ports
Pin assignment of internal ports
The pin assignment of some internal connections is shown in English in the following.
i
Some of the following connectors may be optional!
Front panel
Watch the poling of the LEDs. The positive pole of the connection cables is often indicated with a coloured wire.
Power On/Off Reset
Message LED Power On HD-LED LED 2)
1 2 SCSI LED Input 1) Speaker
1) The same interface 2) 2pin or 3pin connector possible
Connection Reset Power On/Off HD LED SCSI Activity Input Message LED Power On LED Speaker
Note
Attention: Do not connect to the LED connections of an SCSI controller!This connection is intended for a cable with a 4-pin connector. An SCSI controller reports activity (low-active) via this cable. Indicates the system state APM or ACPI together with the Sleep LED (see chapter entitled "APM and ACPI system status, energy-saving modes"). 0, 5 W at 8 Ohm
Power On LED II
1 3
Pin 1 2 3
Signal Power On LED (Anode) Power On LED (Anode) Power On LED (Cathode)
A26361-D1567-Z121-1-6319
English - 11
Pin assignment of internal ports
Serial ATA (internal)
1
Pin 1 3 5 7
Signal GND Transmit data negative Receive data negative GND
Pin 2 4 6 8
Signal Transmit data positive GND Receive data positive Key
IDE/ATA interface
2
1
Pin 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 Signal Reset drive (low asserted) Data 7 (high asserted) Data 6 (high asserted) Data 5 (high asserted) Data 4 (high asserted) Data 3 (high asserted) Data 2 (high asserted) Data 1 (high asserted) Data 0 (high asserted) GND DRQ (high asserted) I/O write (low asserted) I/O read (low asserted) I/O ready (low asserted) DAK (low asserted) IRQ (high asserted) ADR 1 (high asserted) ADR 0 (high asserted) CS 1 (low asserted) IDE-LED (low asserted) Pin 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 Signal GND Data 8 (high asserted) Data 9 (high asserted) Data 10 (high asserted) Data 11 (high asserted) Data 12 (high asserted) Data 13 (high asserted) Data 14 (high asserted) Data 15 (high asserted) Key GND GND GND Cable select GND not connected ATA66 Detect (low asserted) ADR 2 (high asserted) CS 3 (low asserted) GND
12 - English
A26361-D1567-Z121-1-6319
Pin assignment of internal ports
Audio S/PDIF
1
Pin 1 2 3
Signal VCC SPDIF out GND
CD-ROM audio
1
Pin 1 2 3 4
Signal Left CD audio input CD GND CD GND Right CD audio input
AUX audio in
1
Pin 1 2 3 4
Signal Left AUX audio input Analogue GND Analogue GND Right AUX audio input
A26361-D1567-Z121-1-6319
English - 13
Pin assignment of internal ports
Audio port front
1
2
Pin 1 3 5 7 9
Signal Micro input Micro bias Right line output not connected Left line output
Pin 2 4 6 8 10
Signal Analogue GND Analogue VCC Right line return Key Left line return
If the audio front panel is not used, you must plug jumpers on pin pairs 5/6 and 9/10.
USB - dual channel
(internal or external via special cable)
1 11
2 12
Pin 1 3 5 7 9 11
Signal Key VCC C Data negative C Data positive C GND Key
Pin 2 4 6 8 10 12
Signal Chipcard reader on or not connected VCC D Data negative D Data positive D GND not connected
14 - English
A26361-D1567-Z121-1-6319
Pin assignment of internal ports
Serial port 2
1
2
Pin 1 3 5 7 9
Signal DCD 2 SIN 2 SOUT 2 DTR 2 GND
Pin 2 4 6 8
Signal DSR 2 RTS2 CTS 2 RI 2
Fan 1 (CPU)
(processor fan - only for 3 pin fans) Pin 1 2 3 Signal
1
GND Controlled FAN voltage (0V, +6V, . . . Depending on the configuration variant, you must pull a protective foil off the heat sink or coat the heat sink with heat conducting paste before fitting it. Depending on the processor variant, clips may also be supplied for mounting the heat sink that fix it in place. When you have mounted the optional fan, connect the fan plug to the corresponding connection on the mainboard.
A26361-D1567-Z121-1-6319
English - 19
Upgrading main memory
Upgrading main memory
Technical data
Technology: Size:
DDR 266, DDR 333 or DDR 400 unbuffered DIMM modules 184-Pin; 2. 5 V; 64 Bit, no ECC 128 Mbytes up to 4 Gbyte DDR 266 SDRAM 128 Mbytes up to Gbyte DDR 333 SDRAM 128 Mbytes up to Gbyte DDR 400 SDRAM 128, 256, 512 or 1024 Mbyte for one socket
Granularity:
A current list of the memory modules recommended for this mainboard is available on the Internet at: www. fujitsu-siemens. com/mainboards. At least one memory module must be installed. Memory modules with different memory capacities can be combined.
!
You may only use unbuffered 2, 5 V memory modules. Buffered memory modules are not supported. DDR-DIMM memory modules must meet the PC2100, PC2700 or PC3200 specification. The mainboard has two memory channels (channel A and channel B) with two slots each (slot 1 and 3 or slot 2 and 4). The maximum system performance is available when identical memory modules (same order number, same manufacturer, same size, memory density) are used in a memory slot 1 and 2 or memory slot 3 and 4.
slot 4 slot 3
Channel B Channel A
slot 2 slot 1
Number of inserted memory modules slot to be used Channel A, slot 1 Channel A, slot 3 Channel B, slot 2 Channel B, slot 4 X 1 X 2 X 3 X X X 4 X X X X
If you use more than one memory module, then make sure to distribute the memory modules over both memory channels (see table). By doing this you use the performance advantages of the dualchannel mode.
20 - English
A26361-D1567-Z121-1-6319
Upgrading main memory
Memory clock pulse speed
The memory clock pulse speed is affected by the chipset and processor system bus (PSB). The table shows the memory speed in dependence on the Processor System Bus.
System bus (MHz) DDR400 (MHz) DDR333 (MHz) DDR266 (MHz)
800 533 400
Installing a memory module
400 333 266
320 333 266
266 266 266
2
2
Push the holders on each side of the memory slot outwards. [. . . ] Confirm this change by running the BIOS Setup and exiting it again.
Diskette drive A error Diskette drive B error
Check the entry for the diskette drive in the Main menu of the BIOS Setup. Check the connections to the diskette drive.
A26361-D1567-Z121-1-6319
English - 33
Error messages
DMA test failed EISA CMOS not writable Extended RAM Failed at offset: nnnn Extended RAM Failed at address line: nnnn Failing Bits: nnnn Fail-Safe Timer NMI failed Multiple-bit ECC error occurred Memory decreased in size Memory size found by POST differed from EISA CMOS Single-bit ECC error occurred Software NMI failed System memory exceeds the CPU's caching limit System RAM Failed at offset: nnnn Shadow RAM Failed at offset: nnnn
Switch the device off and on again. If the message is still displayed, please contact your sales outlet or customer service centre.
Failure Fixed Disk 0 Failure Fixed Disk 1 Fixed Disk Controller Failure
Check the entry for the hard disk drive in the Main menu and the entry for the IDE drive controller in the Advanced - Peripheral Configuration menu of the BIOS Setup. Check the hard disk drive's connections and jumpers.
Incorrect Drive A - run SETUP Incorrect Drive B - run SETUP
Correct the entry for the diskette drive in the Main menu of the BIOS Setup.
Invalid NVRAM media type
Switch the device off and on again. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE FUJITSU SIEMENS SCENIC EDITION M6
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual FUJITSU SIEMENS SCENIC EDITION M6 will begin.