User manual FUJITSU SIEMENS SCENIC EDITION X102 (P4)

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual FUJITSU SIEMENS SCENIC EDITION X102 (P4). We hope that this FUJITSU SIEMENS SCENIC EDITION X102 (P4) user guide will be useful to you.

Lastmanuals help download the user guide FUJITSU SIEMENS SCENIC EDITION X102 (P4).


Mode d'emploi FUJITSU SIEMENS SCENIC EDITION X102 (P4)
Download
Manual abstract: user guide FUJITSU SIEMENS SCENIC EDITION X102 (P4)

Detailed instructions for use are in the User's Guide.

[. . . ] Any technical problems or other questions you need clarified?Your sales outlet The latest information on our products, tips, updates, etc. , can be found on the Internet under: http://www. All other trademarks referenced are trademarks or registered trademarks of their respective owners, whose protected rights are acknowledged. [. . . ] Line-In and MIC are converted into the function Line-Out with the 6-channel configuration. Depending on driver version and operating system the functions may differ from this presentation. If necessary, further information is provided in the respective help system of drivers and software. Depending on the driver for the audio mode and from the operating system used, you can configure the audio properties, e. Some of the following connectors may be optional!The positive pole of the connection cables is often indicated with a coloured wire. Note Connector for reset switch Connection for ATX On/Off switch Indicates HDD (hard disk) activity Indicates the system state APM or ACPI see "Settings with switches and jumpers" chapter see "Settings with switches and jumpers" chapter Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Signal GND FDHDIN (low asserted) GND not connected Key not connected GND Index (low asserted) GND Motor A Enable (low asserted) GND Drive B Select (low asserted) GND Drive A Select (low asserted) GND Motor B Enable (low asserted) GND Pin 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 Signal Step DIR (low asserted) GND Step Pulse (low asserted) GND Write Data (low asserted) GND Write Enable (low asserted) GND Track 0 (low asserted) GND Write Protect (low asserted) GND Read Data (low asserted) GND Side 1 Select (low asserted) GND Disk Change (low asserted) Pin 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 Signal Reset drive (low asserted) Data 7 (high asserted) Data 6 (high asserted) Data 5 (high asserted) Data 4 (high asserted) Data 3 (high asserted) Data 2 (high asserted) Data 1 (high asserted) Data 0 (high asserted) GND DRQ (high asserted) I/O write (low asserted) I/O read (low asserted) I/O ready (low asserted) DAK (low asserted) IRQ (high asserted) ADR 1 (high asserted) ADR 0 (high asserted) CS 1 (low asserted) IDE-LED (low asserted) Pin 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 Signal GND Data 8 (high asserted) Data 9 (high asserted) Data 10 (high asserted) Data 11 (high asserted) Data 12 (high asserted) Data 13 (high asserted) Data 14 (high asserted) Data 15 (high asserted) Key GND GND GND Cable select GND not connected ATA66 Detect (low asserted) ADR 2 (high asserted) CS 3 (low asserted) GND Setting via control-panel plug connector Pin pair A inserted = Skipping system and BIOS Setup password Pin pair B inserted = System BIOS recovery Pin pair C inserted = factory setting On / inserted System and BIOS Setup password are skipped when the device is switched on and may be changed. Off / not inserted System and BIOS Setup password must be entered when the device is switched on. Recovering System BIOS - pinpair B Pinpair B enables recovery of the old system BIOS after an attempt to update has failed. To restore the old BIOS you need a Flash BIOS Diskette (see "BIOS update" chapter). Off / not inserted Normal operation (default setting). Exit energy-saving mode, switch off the system and remove the power plug from the mains outlet, before carrying out any of the procedures described in this chapter!Even when you have run down the device, parts of the device (e. Memory modules, PCI extension boards) are still energised. Technical data Intel Pentium 4 with 533 or 800 MHz front side bus in the LGA775 design (Value FMB). Celeron with 533 MHz Front Side Bus in the LGA775 design A current list of the processors supported by this mainboard is available on the Internet at: www. Even minor soiling such as grease from the skin can impair the processor's operation or destroy the processor. Place the processor in the socket with extreme care, as the spring contacts of the socket are very delicate and must not be bent. Remove the old processor (2) from the socket. Insert the new processor in the socket so that the marking of the processor is aligned with the marking on the socket (a). Press the lever downward (2) until it is hooked in again (3). Be sure to use heat conducting material between the processor and the heat sink. [. . . ] Missing or invalid NVRAM token Switch the device off and on again. If the message is still displayed, please contact your sales outlet or customer service centre. One or more RDRAM devices are not used One or more RDRAM devices have bad architecture/timing One or more RDRAM devices are disabled Contact your system administrator or contact our customer service centre. If the message is still displayed, please contact your sales outlet or customer service centre. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE FUJITSU SIEMENS SCENIC EDITION X102 (P4)

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual FUJITSU SIEMENS SCENIC EDITION X102 (P4) will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag