User manual FUJITSU SIEMENS SCENIC L (I845)

[. . . ] Please contact: · your sales partner · your sales outlet The latest information on our products, tips, updates, etc. , can be found on the Internet under: http://www. fujitsu-siemens. com or http://www. fujitsu-siemens. com/mainboards Dieses Handbuch wurde auf Recycling-Papier gedruckt. This manual has been printed on recycled paper. Ce manuel est imprimé sur du papier recyclé. Este manual ha sido impreso sobre papel reciclado. [. . . ] Components can become very hot during operation. Ensure you do not touch components when making extensions to the mainboard. The shipped version of this board complies with the requirements of the EEC directive 89/336/EEC "Electromagnetic compatibility". Compliance was tested in a typical PC configuration. When installing the board, refer to the specific installation information in the manual for the receiving device. i The warranty is invalidated if the system is damaged during the installation or replacement of expansions. Information on which expansions you can use is available from your sales outlet or the customer service centre. Information about boards To prevent damage to the mainboard, the components and conductors on it, please take great care when you insert or remove boards. Take great care to ensure that extension boards are slotted in straight, without damaging components or conductors on the mainboard, or any other components, for example EMI spring contacts. Remove the plug from the mains outlet so that system and mainboard are totally disconnected from the mains voltage. Be careful with the locking mechanisms (catches, centring pins etc. ) when you replace the mainboard or components on it, for example memory modules or processors. Never use sharp objects (screwdrivers) for leverage. Boards with electrostatic sensitive devices (ESD) are identifiable by the label shown. The components and connectors marked are not necessarily present on the mainboard. External ports The positions of the external ports are shown on page "Cover". PS/2 keyboard port, purple Serial interface, turquoise PS/2 mouse port, green Parallel port/Printer, burgundy USB - Universal Serial Bus, black LAN LAN connector Audio output (Line out), light green Audio input (Line in), light blue VGA connector, blue (monitor) Microphone jack (mono), pink Speaker out, orange LAN connector This mainboard has an Intel 82547EI LAN controller (10Base-T/100Base-TX/1000 Base-T). The LAN controller is equipped with a 2 KB transmission and receiving buffer (FIFO) and supports WOL function through Magic Packet. The LAN RJ45 connector has two LEDs (light emitting diodes). 1 = Link Mode: the LAN connection is active. WOL mode: a Magic PacketTM is being received. Celeron with 400 MHz Front Side Bus in the mPGA478 design up to 2. 6 GHz. Removing and installing processors Ê Remove the fan that there may be and the heat sink. 3 2 4 5 1 A Pull the lever in the direction of the arrow (1) and lift it as far as it will go (2). Remove the old processor from the socket (3). Insert the new processor in the socket so that the angled corner of the processor matches the coding on the socket (A) with regard to the position (4). Ê Ê Ê i Ê The angled corner of the processor can also be at a different location than shown in the illustration. Push the lever back down until it clicks into place (5). 8 - English A26361-D1644-Z120-1-7419 Replacing processor Mounting heat sink Be sure to use heat conducting material between the processor and the heat sink. If a heat conducting pad (rubber-like foil) is already applied to the heat sink, then use it. [. . . ] Depending on the processor variant, clips may also be supplied for mounting the heat sink that fix it in place. When you have mounted the optional fan, connect the fan plug to the corresponding connection on the mainboard. Ê Ê A26361-D1644-Z120-1-7419 English - 9 Upgrading main memory Upgrading main memory Technical data Technology: Size: Granularity: DDR 266/333/400 unbuffered DIMM modules 184-Pin; 2. 5 V; 64 Bit, no ECC 128 Mbytes to 1 Gbyte DDR 266/333/400 SDRAM 128, 256 or 512 Mbyte for one socket At least one memory module must be installed. You may only use up to two double-sided or two single-sided memory modules for DDR 266/333/400. Memory modules with different memory capacities can be combined. ! You may only use unbuffered 2, 5 V memory modules. [. . . ]