User manual FUJITSU SIEMENS SCENIC N300 (SIS661)

[. . . ] Please contact: · your sales partner · your sales outlet The latest information and updates (e. g. BIOS update) on our mainboards can be found on the Internet under: http://www. fujitsu-siemens. com/mainboards Vous avez . . . . . . des questions techniques ou des problèmes ?Veuillez contacter : · Votre partenaire Commercial · Votre point de Vente Les dernières informations ainsi que les updates (p. ex. BIOS-Update) par rapport à nos cartes mères sont à votre disposition sur Internet : http://www. fujitsu-siemens. com/mainboards Dieses Handbuch wurde auf Recycling-Papier gedruckt. [. . . ] 82562EZ 10 Mbit/s 100 Mbit/s 1000 Mbit/s off yellow 82547EI off green yellow 10 Mbit/s 100 Mbit/s WOL mode: received. a Magic PacketTM is being 82562EZ off yellow 82547EI off green - A26361-D1562-Z121-1-6319 English - 11 Internal ports and connectors Graphics port - Supported screen resolutions Depending on the operating system used, the screen resolutions in the following table refer to the mainboard screen controller. If you are using an external screen controller, you will find details of supported screen resolutions in the operating manual or technical manual supplied with the controller. Screen resolution 640 x 480 800 x 600 1024 x 768 1280 x 1024 1600 x 1200 1920 x 1440 2048 x 1536 Refresh rate (Hz) 120 120 100 100 100 75 60 Colour 32 bit 32 bit 32 bit 32 bit 16 bit 16 bit 16 bit Features 2D+overlay 2D+overlay 2D+overlay 2D 2D 2D 2D Internal ports and connectors The positions of the internal ports and connectors are shown on the Cover. Additional information on some ports is also provided here. Hard disk connection An ultra ATA/66 or ultra ATA/100 hard disk must be connected with a cable especially designed for the ultra ATA/66 or ultra ATA/100 mode. Connect the end of the cable marked with blue to the mainboard. Connect the cable to the hard disk and to the connector on the mainboard. Ê Ê A serial ATA/150 hard disk must be connected with a serial ATA cable. If you have connected one or two hard disks to a serial ATA (one hard disk is possible per serial ATA connection), you must configure the respective settings in the BIOS Setup (further information you can find in the BIOS Setup manual). Audio front panel If you want to use the internal connection for the audio front panel for the front side of the system, then proceed as follows: Remove all plug-in jumpers from the audio front panel connection. Connect the cable for the audio front panel. Ê Ê i If you connect audio devices on both the front and the back of the system, you can only use the connections Line out and Microphone once each. If you have connected audio devices to both Line out connections, only the connection on the front of the system is active. If you have connected audio devices to both Microphone connections, only the connection on the back of the system is active. 12 - English A26361-D1562-Z121-1-6319 Pin assignment of internal ports Pin assignment of internal ports The pin assignment of some internal connections is shown in English in the following. i Some of the following connectors may be optional! Front panel Watch the poling of the LEDs. Otherwise the retaining clips of the heat sink will be damaged. When using an "Intel Boxed" heat sink, the mainboard must be converted. This conversion set is either included with the mainboard or is available separately. If no counter-plate is mounted, you can use both "Intel Boxed" heat sinks and standard heat sinks. If you use the "Intel Boxed" heat sink, the mainboard will bend due to the high pressure of the retaining clips. Depending on the configuration variant, you must pull a protective foil off the heat sink or coat the heat sink with heat conducting paste before fitting it. Depending on the processor variant, clips may also be supplied for mounting the heat sink that fix it in place. When you have mounted the optional fan, connect the fan plug to the corresponding connection on the mainboard. A26361-D1562-Z121-1-6319 English - 21 Upgrading main memory Upgrading main memory Technical data Technology: Size: DDR 266, DDR 333 or DDR 400 unbuffered DIMM modules 184-Pin; 2. 5 V; 64 Bit, no ECC 128 Mbytes up to 4 Gbyte DDR 266 SDRAM 128 Mbytes up to Gbyte DDR 333 SDRAM 128 Mbytes up to Gbyte DDR 400 SDRAM 128, 256, 512 or 1024 Mbyte for one socket Granularity: A current list of the memory modules recommended for this mainboard is available on the Internet at: www. fujitsu-siemens. com/mainboards. At least one memory module must be installed. Memory modules with different memory capacities can be combined. ! You may only use unbuffered 2, 5 V memory modules. Buffered memory modules are not supported. [. . . ] Confirm this change by running the BIOS Setup and exiting it again. Diskette drive A error Diskette drive B error Check the entry for the diskette drive in the Main menu of the BIOS Setup. Check the connections to the diskette drive. 34 - English A26361-D1562-Z121-1-6319 Error messages DMA test failed EISA CMOS not writable Extended RAM Failed at offset: nnnn Extended RAM Failed at address line: nnnn Failing Bits: nnnn Fail-Safe Timer NMI failed Multiple-bit ECC error occurred Memory decreased in size Memory size found by POST differed from EISA CMOS Single-bit ECC error occurred Software NMI failed System memory exceeds the CPU's caching limit System RAM Failed at offset: nnnn Shadow RAM Failed at offset: nnnn Switch the device off and on again. If the message is still displayed, please contact your sales outlet or customer service centre. Failure Fixed Disk 0 Failure Fixed Disk 1 Fixed Disk Controller Failure Check the entry for the hard disk drive in the Main menu and the entry for the IDE drive controller in the Advanced - Peripheral Configuration menu of the BIOS Setup. Check the hard disk drive's connections and jumpers. Incorrect Drive A - run SETUP Incorrect Drive B - run SETUP Correct the entry for the diskette drive in the Main menu of the BIOS Setup. Invalid NVRAM media type Switch the device off and on again. [. . . ]