User manual FUJITSU SIEMENS SCENIC N320 (I865G)

[. . . ] Microsoft, MS, MS-DOS und Windows sind eingetragene Warenzeichen der Microsoft Corporation. PS/2 und OS/2 Warp sind eingetragene Warenzeichen von International Business Machines, Inc. Alle weiteren genannten Warenzeichen sind Warenzeichen oder eingetragene Warenzeichen der jeweiligen Inhaber und werden als geschützt anerkannt. Alle Rechte vorbehalten, insbesondere (auch auszugsweise) die der Übersetzung, des Nachdrucks, der Wiedergabe durch Kopieren oder ähnliche Verfahren. [. . . ] Further information about drivers is provided in the readme files on the hard disk, on the supplied drivers diskettes, on the "Drivers & Utilities" or on the "ServerStart" CD. Notational conventions The meanings of the symbols and fonts used in this manual are as follows: ! i Ê Ë Ú Pay particular attention to text marked with this symbol. Failure to observe this warning endangers your life, destroys the device, or may lead to loss of data. Supplementary information, remarks, and tips follow this symbol. Text which follows this symbol describes activities that must be performed in the order shown. This symbol indicates that you must enter a blank space (press the Space Bar) at this point. This symbol indicates that you must press the Enter key. Text in this typeface indicates screen outputs. Text in this bold typeface indicates the entries you make via the keyboard. Text in italics indicates commands or menu items. "Quotation marks" indicate names of chapters or terms. Important notes Store this manual close to the device. If you pass the device on to third parties, you should pass this manual on with it. Be sure to read this page carefully and note the information before you open the device. You cannot access the system board components without first opening the device. 1 AGP slot The AGP slot supports 1x, 2x and 4x AGP mode. The voltage is detected and configured automatically. 1 CNR type B slot IDE hard disk controller connected to PCI bus for up to four IDE drives (e. g. IDE hard disk drives, ATAPI CD-ROM drives) The IDE hard disk controller are ATA33/66/100, ultra DMA capable and support PIO modes 04. Floppy disk drive controller (possible formats: 720 KB, 1. 44 MB, 2. 88 MB) The system board supports booting from a 120 MB IDE floppy disk drive. 1 external parallel port (ECP- and EPP-compatible) 1 external serial port (16C550 compatible with FIFO) 1 external serial port (16C550 compatible with FIFO) 1 internal chipcard reader interface (SmartCard reader). This interface can also be used as a second serial port (16C550 compatible with FIFO). 1 internal WOL interface 2 external PS/2 ports for keyboard and mouse 2 external USB ports USB ports D, E, F (internal) Real-time clock/calendar with integrated battery backup · · · · · · · · · · · 4 - English A26361-D1238-Z120-2-7419 Features Interfaces and connectors DIMM 3 DIMM 2 DIMM 1 AGP PCI 1 PCI 2 PCI 3 1 3 4 5 6 7 2 8a 8b8c 1= 2= 3= 4= 5= PS/2 mouse port PS/2 keyboard port USB ports 1 and 2 Serial port 1 Parallel port 6 = Serial port 2 7 = Game/Midi port 8a = Audio Line-Out 8b = Audio Line-In 8c = Audio Micro-In The components and connectors marked are not necessarily present on the system board. CNR A26361-D1238-Z120-2-7419 English - 5 Features 1 23 4 5 67 16 DIMM 3 DIMM 2 DIMM 1 8 9 10 11 AGP 15 12 PCI 1 PCI 2 PCI 3 14 Chipcard reader interface or serial port 2 Power supply monitoring Cover monitoring Floppy disk drive IDE drives 3 and 4 (secondary) IDE drives 1 and 2 (primary) Connector for control panel and loudspeaker 8 = Wake On LAN 1= 2= 3= 4= 5= 6= 7= 13 9 = USB port F 10 = USB port E 11 = USB port D 12 = Fan 2 (e. for the processor) 13 = CD audio input 14 = AUX audio input 15 = Fan 1 (e. for the processor) 16 = Power supply The components and connectors marked are not necessarily present on the system board. Hard disk connection An ultra ATA/66 or ultra ATA/100 hard disk must be connected with a cable especially designed for the ultra ATA/66or ultra ATA/100 mode. Ê Connect the end of the cable marked with blue to the system board. 6 - English CNR A26361-D1238-Z120-2-7419 Settings with switches and jumpers Settings with switches and jumpers 4321 ON DIMM 3 DIMM 2 DIMM 1 AGP PCI 1 PCI 2 PCI 3 Switch 1 = must be set to off Switch 2 = System BIOS recovery Switch 3 = Write-protection for floppy disk Switch 4 = must be set to off i The clock frequency of the processor is set automatically. Recovering System BIOS - switch 2 Switch 2 enables recovery of the old system BIOS after an attempt to update has failed. To restore the old system BIOS you need a Flash BIOS Diskette (please call our customer service centre). [. . . ] Hävitä käytetty paristo valmistajan ohjeiden mukaisesti. VARNING Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren. Kassera använt batteri enligt fabrikantens instruktion. [. . . ]