User manual FUJITSU SIEMENS SCENIC N320 (SIS661+)

[. . . ] any technical problems or other questions you need clarified?Please contact: · your sales partner · your sales outlet You will find further information in the manual "Safety, Guarantee and Ergonomics" . The latest information on our products, tips, updates, etc. , can be found on the Internet under: http://www. fujitsu-siemens. com Dieses Handbuch wurde auf Recycling-Papier gedruckt. This manual has been printed on recycled paper. [. . . ] Be sure to read this page carefully and note the information before you open the device. You cannot access the components of the system board without first opening the device. How to dismantle and reassemble the device is described in the Operating Manual accompanying the device. Please note the information provided in the chapter "Safety" in the Operating Manual of the device. Incorrect replacement of the lithium battery may lead to a risk of explosion. It is therefore essential to observe the instructions in the chapter , , dd-on modules" - , , Replacing the A lithium battery". ! A26361-D1192-Z120-2-7419 English - 1 Important notes The shipped version of this board complies with the requirements of the EEC directive 89/336/EEC "Electromagnetic compatibility". Compliance was tested in a typical PC configuration. When installing the board, refer to the specific installation information in the Operating Manual or Technical Manual of the receiving device. Connecting cables for peripherals must be adequately insulated to avoid interference. ! i Components can become very hot during operation. Make sure you do not touch components when making extensions to the system board. There is a danger of burns!The warranty is invalidated if the device is damaged during the installation or replacement of system expansions. Information on which system expansions you can use is available from your sales outlet or the customer service center. Information on boards To prevent damage to the system board or the components and conductors on it, please take great care when you insert or remove boards. Take care above all to ensure that extension boards are slotted in straight without damaging components or conductors on the system board, or any other components, for example EMI spring contacts. This port does not support the ring indicator signal. 1 internal WOL interface 2 external PS/2 ports for keyboard and mouse 2 external USB ports Real-time clock/calendar with integrated battery backup 4 - English A26361-D1192-Z120-2-7419 Features Interfaces and connectors RIMM 4 RIMM 3 RIMM 2 RIMM 1 AGP Pro PCI 4 PCI 1 PCI 2 PCI 3 PCI 5 1 3 5 7 8 2 4 6 9a 9b9c 1= 2= 3= 4= 5= 6= 7= PS/2 mouse port PS/2 keyboard port Parallel port Serial port 1 USB port 2 USB port 1 LAN port 8 = Game/Midi port 9a = Audio Line-Out 9b = Audio Line-In 9c = Audio Micro-In The components and connectors marked are not necessarily present on the system board. CNR A26361-D1192-Z120-2-7419 English - 5 Features 1 23 4 5 6 7 89 10 RIMM 4 RIMM 3 RIMM 2 RIMM 1 19 AGP Pro 11 12 13 PCI 4 PCI 2 PCI 3 PCI 5 PCI 1 18 17 16 15 14 1= 2= 3= 4= 5= 6= 7= Power supply monitoring Connector for control panel and loudspeaker Power supply IDE drives 3 and 4 (secondary) Floppy disk drive IDE drives 1 and 2 (primary) Serial chipcard reader interface or serial port 2 8 = Fan 2 (AUX) 9 = IrDA 10 = 11 = 12 = 13 = 14 = 15 = 16 = 17 = 18 = 19 = I²C port Cover monitoring USB chipcard reader or USB front panel Wake On LAN (WOL) CD audio input AUX audio input Power supply +3. 3 V for AGP Pro Power supply +12 V Fan (system) Fan 1 (for the processor) The components and connectors marked are not necessarily present on the system board. 6 - English A26361-D1192-Z120-2-7419 CNR Features Temperature monitoring / system monitoring One goal of temperature and system monitoring is to reliably protect the computer hardware against damage caused by overheating. The LAN controller is equipped with a 3Kbyte . transmission and receiving buffer (FIFO) and supports the WOL function through Magic Packet It is also possible to boot a device without its own boot hard disk via LAN. Here Bootix LAN BootP and Intel PXE are supported. The LAN RJ45 connector is equipped with a yellow and a green LED (light emitting diode). 1 = Yellow indicator 2 = Green indicator 1 2 Green Yellow a connection exists (e. Link Mode: WOL mode: the LAN connection is active. TM a Magic Packet is being received. 8 - English A26361-D1192-Z120-2-7419 Features PCI bus interrupts The following table shows which PCI bus interrupts on the system board are assigned. PCI bus interrupt B, C, D, A C, D, A, B D, A, B, C A, B, C, D B, C, D, A A, B D D A B B Component on system board: PCI bus slot 1 PCI bus slot 2 PCI bus slot 3 PCI bus slot 4 PCI bus slot 5 AGP slot USB controller LAN controller Graphics processor SMBus AC'97 Audio A26361-D1192-Z120-2-7419 English - 9 Settings with switches and jumpers Settings with switches and jumpers RIMM 4 RIMM 3 RIMM 2 RIMM 1 4321 AGP Pro ON PCI 4 PCI 1 PCI 2 PCI 3 PCI 5 Switch 1 = must be set to off Switch 2 = System BIOS recovery Switch 3 = Write-protection for floppy disk Switch 4 = must be set to off i The clock frequency of the processor is set automatically. Recovering System BIOS - switch 2 Switch 2 enables recovery of the old system BIOS after an attempt to update has failed. To restore the old system BIOS you need a Flash BIOS Diskette (please call our customer service center). On Off The System BIOS executes from floppy drive A: and the inserted "Flash-BIOSDiskette" restores the System BIOS on the system board. Normal operation (default setting). Write protection for floppy disks - switch 3 Switch 3 is used to define whether floppy disks can be written or deleted in the floppy disk drive. [. . . ] This C-RIMM must then be installed in the order of the locationsbehind the RIMM: Location bank 0 = RIMM Location bank 1 = C-RIMM. The system board supports only 32 RDRAM for each bank: Total size of RIMM 64Mbit technology 128Mbit technology 128 Mbyte 128 Mbyte 192 Mbyte 256 Mbyte 128 Mbyte 256 Mbyte 384 Mbyte 512 Mbyte Number of chips 16 8 12 16 4 8 12 16 256Mbit technology ! The system board supports memory modules PC800 and PC600. Always use memory modules of the same speed class. You should not mix memory modules that have different speed classes. Optimal system speed is achieved when you use PC800 RDRAM memory modules. A26361-D1192-Z120-2-7419 English - 13 Add-on modules Installing memory modules 2 2 Ê Ê Ê Flip the holders on each side of the relevant location outwards. Insert the memory module into the location(1). [. . . ]