User manual FUJITSU SIEMENS SCENIC PRO C5

[. . . ] any technical problems or other questions you need clarified?Please contact: · your sales partner · your sales outlet You will find further information in the manual "Safety, Warranty and Ergonomics". The latest information on our products, tips, updates, etc. , can be found on the Internet under: http://www. fujitsu-siemens. com Dieses Handbuch wurde auf Recycling-Papier gedruckt. This manual has been printed on recycled paper. [. . . ] Alle Rechte vorbehalten, insbesondere für den Fall der Patenterteilung oder GM-Eintragung. How to dismantle and reassemble the device is described in the Operating Manual accompanying the device. Please observe the safety information provided in the "Important notes" chapter in the device's operating manual. Incorrect replacement of the lithium battery may lead to a risk of explosion. It is therefore essential to observe the instructions in the "Add-on modules" - "Replacing the lithium battery" section. A26361-D1214-Z120-4-7419 English - 1 Important notes The shipped version of this board complies with the requirements of the EEC directive 89/336/EEC "Electromagnetic compatibility". Compliance was tested in a typical PC configuration. When installing the board, refer to the specific installation information in the Operating Manual or Technical Manual for the receiving device. Connecting cables for peripherals must be adequately shielded to avoid interference. ! i Components can become very hot during operation. Ensure you do not touch components when making extensions to the system board. The warranty is invalidated if the device is damaged during the installation or replacement of system expansions. Information on which system expansions you can use is available from your sales outlet or the customer service centre. Information about boards To prevent damage to the system board or the components and conductors on it, please take great care when you insert or remove boards. 1 internal WOL interface 2 external PS/2 ports for keyboard and mouse 2 external USB ports 1 internal USB port or 2 internal USB ports Real-time clock/calendar with integrated battery backup · · · · · · · · · · · · External ports 1 3 5 6 7 8 2 4 9a 9b9c 1= 2= 3= 4= 5= 6= PS/2 mouse port PS/2 keyboard port LAN connector USB ports 1 and 2 Serial port 1 Parallel port 7 = VGA port 8 = Game/Midi port 9a = Audio Line-Out / Headphones 9b = Audio Line-In 9c = Audio Micro-In The components and connectors marked are not necessarily present on the system board. 4 - English A26361-D1214-Z120-4-7419 Features Internal ports and connectors 1 2 3 4 5 6 78 14 DIMM 2 DIMM 1 9 10 AGP / GPA PCI 1 13 PCI 2 PCI 3 12 11 1= 2= 3= 4= 5= 6= Power supply Chipcard reader interface or serial port 2 Floppy Disk Drive IDE drives 3 and 4 (secondary) IDE drives 1 and 2 (primary) Connector for control panel and loudspeaker 7 = Fan 2 (e. g. for the processor) 8 = Wake On LAN 9 = USB port 4 10 = USB port 3 11 = CD audio input 12 = AUX audio input 13 = Fan 1 (e. g. for the processor) 14 = Cover monitoring The components and connectors marked are not necessarily present on the system board. CNR A26361-D1214-Z120-4-7419 English - 5 Features Hard disk connection An ultra ATA/66 or ultra ATA/100 hard disk must be connected with a cable especially designed for the ultra ATA/66or ultra ATA/100 mode. Ê Connect the end of the cable marked with blue to the system board. LAN connector This system board has an optional Intel 82550TM LAN controller which supports transfer speeds of 10 Mbit/s and 100 Mbit/s. The LAN controller is equipped with a 3 KB transmission and receiving buffer (FIFO) and supports WOL function through Magic Packetä. To restore the old system BIOS you need a Flash BIOS Diskette (please call our customer service centre). On Off The System BIOS executes from floppy drive A: and the inserted "Flash-BIOSDiskette" restores the System BIOS on the system board. Normal operation (default setting). Write protection for floppy disks - switch 3 Switch 3 is used to define whether floppy disks can be written or deleted in the floppy disk drive. To write and delete floppy disks, the write-protection in BIOS Setup must be disabled (in menu Security, the field Diskette Write must be set to Enabled). On Off The floppy disk drive is write-protected. Floppy disks can be read, written and deleted (default setting). 8 - English CNR A26361-D1214-Z120-4-7419 Add-on modules Add-on modules ! Exit Suspend mode, switch off the device and remove the power plug from the mains supply, before carrying out any of the procedures described in this chapter!Even when you have switched off the device, parts (e. g. [. . . ] If PC133 memory modules are used, only 2 single sided or 2 double sided memory modules are supported. Installing a memory module 2 2 Ê Ê Ê Push the holders on each side of the memory compartment outwards. Insert the memory module into the location (1). At the same time flip the lateral holders upwards until the memory module snaps in place (2). Removing a memory module 1 1 Ê Ê Push the clips on the right and left of the compartment outward (1). Carefully remove the memory module from the compartment (2). A26361-D1214-Z120-4-7419 English - 11 Add-on modules Upgrading an AGP screen controller or the GPA memory AGP screen controllers with 1x, 2x and 4x AGP modes are supported. [. . . ]