User manual FUJITSU SIEMENS SCENIC PRO C5/D5/M5

[. . . ] Please contact: your sales partner your sales outlet Further information can be found in the "Safety and Ergonomics" and "Warranty" manuals. BIOS update) on our mainboards can be found on the Internet under: http://www. fujitsu-siemens. com (Services & Support). Dieses Handbuch wurde auf Recycling-Papier gedruckt. This manual has been printed on recycled paper. Ce manuel est imprimé sur du papier recyclé. [. . . ] Even when you have run down the device, parts of the device (e. g. memory modules, PCI extension boards) are still energised. Installing and removing processors Technical data Intel Pentium 4 with 533 or 800 MHz front side bus in the LGA775 design (Value FMB). A current list of the processors supported by this mainboard is available on the Internet at: www. fujitsu-siemens. com. Installing processor with heat sink ! Never touch the underside of the processor. Even minor soiling such as grease from the skin can impair the processor's operation or destroy the processor. Place the processor in the socket with extreme care, as the spring contacts of the socket are very delicate and must not be bent. Remove the heat sink. 2 1 Press down the lever (1) and unhook it. Remove the old processor (2) from the socket. 12 - English A26361-D1944-Z120-1-7419, edition 1 Add-on modules / Upgrading a Insert the new processor in the socket so that the marking of the processor is aligned with the marking on the socket (a). 1 2 3 Fold down the frame (1). Press the lever downward (2) until it is hooked in again (3). A26361-D1944-Z120-1-7419, edition 1 English - 13 Add-on modules / Upgrading Mounting heat sink i Use only the heat sink supplied with your system! Be sure to use heat conducting material between the processor and the heat sink. If a heat conducting pad (rubber-like foil) is already applied to the heat sink, then use it. Otherwise you must apply a very thin layer of heat conducting paste. Heat conducting pads can only be used once. The lithium battery must then be replaced. ! Incorrect replacement of the lithium battery may lead to a risk of explosion!The lithium battery may be replaced only with an identical battery or with a type recommended by the manufacturer. Do not throw lithium batteries into the household waste. They must be disposed of in accordance with local regulations concerning special waste. Make sure that you insert the battery the right way round. The plus pole must be on the top! The lithium battery holder exists in different designs that function in the same way. 2 3 3 2 1 3 Press the locking lug in the direction of the arrow; the battery jumps somewhat out of the holder (1). Insert a new lithium battery of the same type into the socket (3). A26361-D1944-Z120-1-7419, edition 1 English - 19 Add-on modules / Upgrading BIOS update When should a BIOS update be carried out? Fujitsu Siemens Computers makes new BIOS versions available to ensure compatibility to new operating systems, new software or new hardware. In addition, new BIOS functions can also be integrated. A BIOS update should always also be carried out when a problem exists that cannot be solved with new drivers or new software. Where can I obtain BIOS updates? The BIOS updates are available on the Internet at www. fujitsu-siemens. com. How does a BIOS update work? You have two ways of doing this: 1. BIOS update under DOS with bootable BIOS update floppy disk - brief description Download the update file from out website to your PC. Plug an external USB floppy disk drive or a configured removable USB medium (e. g. [. . . ] If the message is still displayed, please contact your sales outlet or customer service centre. Service Processor not properly installed The server management controller has not been correctly installed. If the message is still displayed, please contact your sales outlet or customer service centre. System battery is dead - Replace and run SETUP Replace the lithium battery on the mainboard and redo the settings in the BIOS Setup. [. . . ]