User manual FUJITSU SIEMENS SCENIC PRO C6/D6/M6

[. . . ] System board D983 Technical Manual Is there . . . . . . any technical problem or other question you need clarified?Please contact: · one of our IT Service Shops · your sales partner · your sales office The addresses of your service partners are contained in the guarantee booklet or in the service address booklet. The latest information on our products, tips, updates, etc. , can be found on the Internet under: http://www. siemens. com/pc . . . [. . . ] USB Controller switches the USB controller (Universal Serial Bus) of the system board on or off. Enabled The system BIOS determines which system resources (interrupts, addresses) are occupied. Disabled The USB controller is disabled (default entry). 26 A26361-D983-Z120-7-7619 Advanced - System settings Settings in BIOS Setup PCI Configuration calls the submenu in which you can make the settings for the PCI slots. Phoenix BIOS Setup Advanced PCI Configuration PCI PCI PCI PCI Interrupt Interrupt Interrupt Interrupt Mapping Mapping Mapping Mapping INTA#: INTB#: INTC#: INTD#: [Auto] [Auto] [Auto] [Auto] [Disabled] [Yes] [0040] [Yes] [0040] [Yes] [0040] -/+ Enter Change Values Execute Command F9 Setup Defaults F7 Previous Values Item Specific Help VGA Interrupt: PCI Device, Slot #1 Default Latency Timer: Latency Timer: PCI Device, Slot #2 Default Latency Timer: Latency Timer: PCI Device, Slot #3 Default Latency Timer: Latency Timer: F1 Help ESC Exit Select Item Select Menu Example for submenu PCI Configuration A26361-D983-Z120-7-7619 27 Settings in BIOS Setup Advanced - System settings PCI Interrupt Mapping INTx# defines which PCI interrupt is switched to which ISA interrupt. For the change to take effect, you must switch your PC off and then on again after the BIOS Setup has terminated. With multifunctional PCI boards, all PCI interrupts can be used. The controllers on the system board do not need any PCI interrupts. If you use a setting other than Auto, the Plug&Play functionality of the system BIOS for PCI boards is deactivated. The PCI interrupts INTA#, INTB# and INTC# are assigned as follows: PCI slot 1 = INTA#, PCI slot 2 = INTB#, PCI slot 3 = INTC# Auto The PCI interrupts are assigned automatically in accordance with the Plug&Play guidelines (default entry). Disabled No PCI interrupt is used for the PCI board in the assigned PCI slot. IRQ03, IRQ04, IRQ05, IRQ06, IRQ07, IRQ09, IRQ10, IRQ11, IRQ12, IRQ14, IRQ15 The PCI interrupt is switched to the selected ISA interrupt. You may not select an ISA interrupt that is used by a component on the system board (e. g. VGA Interrupt assigns PCI interrupt to the monitor controller on the built-in PCI module. If you have not defined any other interrupt with PCI Interrupt Mapping, IRQ9 is assigned. Enabled The interrupt is assigned to the monitor controller on the built-in PCI module. Disabled The interrupt can be used for other add-on modules (default entry). 28 A26361-D983-Z120-7-7619 Advanced - System settings Settings in BIOS Setup PCI Device, Slot #n: Default Latency Timer specifies the lowest number of clock cycles in which a PCI master module can be active at the PCI bus. n stands for the number of the PCI slot. For the change to take effect, you must switch your PC off and then on again after the BIOS Setup has terminated. Yes The value predefined by the PCI module is accepted. The entry in the corresponding field for PCI Device, Slot #n: Latency Timer is ignored. No The value predefined by the PCI module is ignored. The value set in the corresponding field for PCI Device, Slot #n: Latency Timer determines the number of clock cycles. PCI Device, Slot #n: Latency Timer Requirement: The corresponding field for PCI Device, Slot #n: Default Latency Timer must be set to No. The field defines the lowest number of clock cycles in which a burst can be transferred on the PCI bus. [. . . ] Om du trycker på funktionstangenten [F1] startas PCn med den ofullständige systemkonfigurationen. Om meddelandet fortfarande visas bör du kontakta din återförsäljare eller vår kundservice. Real time clock failure Ropa upp BIOS-Setup-menyn och ställ in korrekt klockslag i menyn Main. Om meddelandet fortfarande visas bör du kontakta din återförsäljare eller vår kundservice. . System battery is dead - Replace and run SETUP Byt ut litiumbatteriet på systemkomponenten och genomför inställningarna i BIOS-Setup-menyn på nytt. System Cache Error - Cache disabled Starta upp PCn på nytt. Om meddelandet fortfarande visas bör du kontakta din återförsäljare eller vår kundservice. System CMOS checksum bad - run SETUP Ropa upp BIOS-Setup-menyn. [. . . ]