User manual FUJITSU SIEMENS SCENIC PRO M7

[. . . ] any technical problem or other question you need clarified?Please contact: · one of our service partners · your sales partner · your sales outlet The addresses of your service partners are contained in the guarantee booklet or in the service address booklet. The latest information on our products, tips, updates, etc. , can be found on the Internet under: http://www. fujitsu-siemens. com Dieses Handbuch wurde auf Recycling-Papier gedruckt. This manual has been printed on recycled paper. [. . . ] Never touch pins or conductors on boards fitted with ESDs. 2 - English A26361-D1107-Z120-14-7419 Features Features The components and connectors marked do not have to be present on the system board. · · or System board in ATX format Intel Pentium II processor with 100 MHz or 66 MHz Front Side Bus for slot 1 processor socket Intel Pentium III processor with 100 MHz Front Side Bus for slot 1 processor socket Intel Celeron processor with 66 MHz Front Side Bus for slot 1 processor socket · or · · · · · · · Intel Pentium II / III and Celeron processors support MMX technology. Size and frequency of firstlevel cache and second-level cache are depending on the processor used. Intel chipset 440BX / PIIX4E Intel 82559 LAN controller (10/100 Mbit/s) with RJ45 interface WOL with Magic Packetä is supported, as is booting from LAN with Bootix LAN BootP or Intel LSA. Fujitsu Siemens system monitoring and temperature management 3 DIMM slots for 16 to 768 Mbyte main memory (SDRAM memory modules) Flash BIOS Energy saving functions - - - ACPI S3 / Save-to-RAM (requires an operating system that supports ACPI). ACPI S4 / Save-to-Disk (requires an operating system that supports ACPI). APM Chipcard reader interface Detection of unauthorized opening of the housing Simple error detection and correction in the main memory with an ECC System, Setup and Keyboard password parallel and serial ports can be deactivated Write protection for floppy disk drive Virus warning function for the boot hard disk Virus protection function for the flash BIOS and the EEPROMs on the memory modules · Security functions: - - - - - - - - · · 1 AGP slot, 4 PCI slots AGP and PCI slots support 3. 3 V main and auxiliary voltages. 1 ISA/PCI slot (shared) and 1 ISA slot or 2 ISA slots A26361-D1107-Z120-14-7419 English - 3 Features · · · · · · · · · · · IDE hard disk controller connected to PCI bus for up to four IDE drives (e. g. IDE hard disk drives, ATAPI CD-ROM drives) The IDE hard disk controller are ultra DMA33 mode capable and support PIO modes 0-4. Floppy disk drive controller (possible formats: 720 Kbyte, 1. 44 Mbyte) The system board supports booting from a 120 Mbyte IDE floppy disk drive. 1 external parallel interface (ECP- and EPP-compatible) 1 external serial port (16C550 compatible with FIFO) 1 internal chipcard reader interface As an alternative this interface can also be used as a second serial port (16C550 compatible with FIFO). 1 internal WOL interface 2 external PS/2 interfaces for keyboard and mouse 2 external USB ports (USB = Universal Serial Bus) 1 connector for internal infrared connection Real-time clock/calendar with integrated battery backup 4 - English A26361-D1107-Z120-14-7419 Features Interfaces and connectors 1 23 AGP ISA2 PCI 3 PCI 2 Slot 1 2 5 1 1 = Serial port 1 2 = PS/2 mouse port 3 = PS/2 keyboard port 3 4 6 7 4= 5= 6= 7= Parallel port USB port 2 USB port 1 LAN port The components and connectors marked do not have to be present on the system board. PCI 1 PCI5 PCI4 ISA1 A26361-D1107-Z120-14-7419 English - 5 Features 1 23 4 5 67 8 9 10 11 15 14 1 23 13 AGP ISA2 ISA1 PCI 3 PCI 2 Slot 1 12 1 = I2C connector 2 = Serial chipcard reader interface or serial port 2 3 = Power supply 4 = Floppy disk drive 5 = IDE drives 3 and 4 (secondary) 6 = Wake On LAN 7 = ON/OFF switch 8 = Fan 2 9 = IDE drives 1 and 2 (primary) 10 = Connector for front panel 11 = IrDA 12 = USB chipcard reader 13 = Fan 1 (e. The components and connectors marked do not have to be present on the system board. PCI 1 PCI5 PCI4 A26361-D1107-Z120-14-7419 ISA1 English - 13 Add-on modules Installing / removing processor Installing the processor i If you wish to upgrade your system with a new processor, the processor bracket on the system board may need to be replaced beforehand. Should it be necessary to replace the bracket, please contact our customer service center. Depending on the design of the processor housing, the heat sink can be moved on the processor and the processor in the bracket. This floating suspension in the installed state ensures reliable contact between the processor and the heat sink. Detents in the bracket prevent the processor from slipping out. If the heat sink on the processor can be moved, then it must also be possible to move the mounted processor in the bracket. If you replace the processor, grasp the processor housing by the processor and the heat sink. (A) 2 2 (B) 2 1 2 1 1 1 The illustration shows two bracket and processor models. Ê Ê Ê Ê Ê Remove the old processor if necessary. Slide the processor into the bracket (1). Push the processor down in the bracket and press it into the slot until the clamps (2) to the left and right snap into place. Set the clock frequency of the new processor using switches 5 to 8 of the switch block. If the processor has a temperature sensor or a fan, attach the associated cable to the connector for the temperature sensor or the fan on the system board. Removing the processor Ê Ê If the processor has a temperature sensor or a fan, pull out the associated cable. [. . . ] Front Side Bus FWH . . . . . . . . . . . . . . . . . . . . . . . . . . . . Firmware Hub GMCH . . . . . . . . . . . . . . . . . . . . . . . . . Graphics and Memory Controller Hub I2C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Inter Integrated Circuit IAPC. . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]