User manual FUJITSU SIEMENS SCENIC T (I815E)

[. . . ] Please contact: our Hotline: Tel. : (01923) 209 109 your sales partner your sales office . . . anything you want to tell us about this manual?Please send us your comments quoting the order number of the manual. Siemens Nixdorf Informationssysteme AG User Documentation Department, BS2000 OS ID4 Otto-Hahn-Ring 6 D-81730 München i Only SCENIC-certified components guarantee the described SCENIC functionality. Introduction Important notes Your training needs? SCENIC PS Preparation for use and operation The Siemens Nixdorf Training Centers offer you a wide range of training courses in information technology and on IT products and other subjects - onsite near to your workplace or offsite at one of our training centers. [. . . ] If the mouse controller is disabled, you will not be able to operate either the supplied mouse nor a mouse connected to the PS/2 mouse port. Depending on the keyboard type, plug the other connector of the keyboard cable into the socket on the underside (left) of the keyboard or into the righthand socket on the rear of the keyboard (right). Connecting devices with serial or parallel ports Connect the data cable to the external device. Connect the data cable of the external device to the appropriate port on the system unit. Connecting the mouse to the keyboard i If your mouse has an angular connector, it must be connected to the keyboard. i Most devices that you connect to the serial or parallel port require special drivers. MS-Windows already includes many drivers but if the driver you need is not on the hard disk please install it from the floppy disk supplied with the device or with the application program. If you need to change the default settings of the serial or parallel port (e. address, interrupt), you can do so in the BIOS Setup. The default settings of the ports are given in the Technical Manual for the system board. Plug the connector of the mouse cable into the left-hand socket on the rear of the keyboard. Fit the mouse cable into the corresponding guide on the underside of the keyboard. In the mouse device connected to the keyboard the upper part (hand support with buttons) can be swivelled to the left or right. Adjust it so that your hand is in a comfortable relaxed position when using the mouse. A26361-K405-Z111-2-7619 17 18 A26361-K405-Z111-2-7619 Connecting devices Preparation for use and operation Preparation for use and operation Connecting devices Connecting loudspeakers, a microphone and audio devices Plug the data cable of the monitor into the monitor port (15-pin) of the system unit. If the system unit has two CRT controllers, connect the data cable to the second controller. i Only on a system unit with audio functionality. 2 Only active loudspeakers may be used. The external microphone must be a dynamic microphone or a condenser microphone. Connect the cable of the external loudspeakers to the audio output of the system unit. Generate the utility and driver diskettes using the batch files in the \PROGS\DISKS directory and label them. i The main switch and ON/OFF switch do not cut off power voltage from the system unit. To cut off the power supply, you must pull out the power plug. Switching the PC ready-to-operate by means of software You can put your PC into ready-to-operate mode in Windows 95 choosing Shut down in the Start menu or using the DeskOff program: Prerequisite: Your system must support switching off with software and this functionality must be enabled in BIOS-Setup (Soft Power OFF - Enabled). Switching on the PC Switch on the monitor (see the Operating Manual of the monitor). Use the main switch on the rear of system unit to switch the system unit on. Exit MS-Windows (choosing Shut down in the Start menu). The PC switches to the mode which was active when it was last switched off: If the Power ON display on the front of the system unit lights up orange, press the ON/OFF switch on the front of the system unit. The system unit is ready-to-operate, and the the Power ON display lights up orange. A26361-K405-Z111-2-7619 23 24 A26361-K405-Z111-2-7619 Connecting a MIDI Preparation for use and operation Preparation for use and operation Connecting a MIDI Connecting a MIDI i You need a Game/MIDI port and a commercially available MIDI interface box or Soundblaster-compatible MIDI adapter cable . Connect the Game/MIDI port to the MIDI interface box. Connect the MIDI output of your keyboard to the MIDI input of the MIDI interface box. Connect the MIDI input of your keyboard to the MIDI output of the MIDI interface box. Switch on the device. Recording a MIDI file Press the Record button. Save the MIDI file with File - Save. Playing back a MIDI file Press the Play button. You must now also change the basic configuration of your system accordingly. Enable the MIDI interface with: Start - Settings - Control Panel - System icon Device-Manager index tab. Select the Resources index tab under Sound, video and game controllers for the setting Creative Labs Sound Blaster 16 or AWE 32. Disable the setting Use automatic settings. [. . . ] You must remove the slot board and the drive carrier before you can remove the floppy disk drive and the hard disk drive. This is not necessary when removing the CD-ROM drive. Fasten the screw (1). 1 3 2 1 Remove the screw (1). Pull the drive carrier out of the device (2) and put it on ist side (3). Remove the two screws (1). Removing the drive carrier 1 2 Unplug the connectors from the floppy disk drive and from the hard disk drive. Loosen the screw (1). Push the floppy disk drive in the direction of the arrow (2). A26361-K405-Z111-2-7619 55 56 A26361-K405-Z111-2-7619 Changing boards System expansions System expansions Changing boards Replacing the floppy disk drive 2 1 2 1 Remove the screw (1) and pull the floppy disk drive out of the drive carrier (2). Push the floppy disk drive into the metal support (1) and fasten it with the four screws (2). 1 2 1 2 Remove the four screws (1) and pull the floppy disk drive out of the metal support (2). [. . . ]